%106'06R Answering System Features ............................... 1 Caller ID Features ............................................... 2 Installation ........................................................... 2 Connecting the System ....................................... 2 Installing a Backup Battery .................................. 2 Answering System ............................................... 2 Preparation .......................................................... 2 Turning the System

O NOTE O The USOC number of thejackto beinstalledis RJ11C (or RJ11W for a wall plate jack). Attached Phone Line Cord Wall Jack DC 9V Jack Modular Phone Line Cord AC Power Cord TEL LINE Jack Attached Phone Line Cord Wall Jack DC 9V Jack Modular Phone Line Cord AC Power Cord TEL LINE Jack Preparation 7 Preparation Preparation O NOTE O Hold down SKIP/ TIME SET/CHECK continuously for Steps 1–4. TURNING THE SYSTEM ON/ OFF To turn on the system, press ON/OFF/ STOP. The display lights and the system so

Contents Features 3 Introduction 4 Selecting a Location 4 Installing the Charger 5 Connecting/Charging the Battery 5 Installing a Belt Clip 8 Using an Optional Headset 8 Registering the Handset 9 Resetting Handsets 10 Resetting the Handset Without the Base 11 Controls & Functions 12 Reading the Display 13 Using Your Accessory Handset 17 Using Hold, Conference, Transfer and Intercom 23 Care 25 Service and Repair 25 FCC Statement 25 Glossary 27 Limited One-Year Warranty 28 Features Additional Hand

... ... ..7 771 115 55. ..3 338 886 66. ..8 888 886 661 11i iin nnf ffo oo@ @@v vvi iik kki iin nng gge eel lle eec cct ttr rro oon nni iic ccs ss. ..c cco oom mmh hht ttt ttp pp: ::/ /// //w www www ww. ..v vvi iik kki iin nng gge eel lle eec cct ttr rro oon nni iic ccs ss. ..c cco oom mm The SQRG-12 Sequential Ring Generator is designed for applications where more than one person answers incoming calls and those persons may be in locations where the TMS-6X or TMS-12A is not visible. The SQRG-1

To turn on the base’s ringer, set RINGER to ON. SETTING THE HANDSET’S RINGER VOLUME At any time except during a call, press t or s to set the handset’s ringer volume. The phone rings at the selected volume and the display shows Ringer Low or Ringer High. SETTING THE NUMBER OF RINGS Set RING TIME on the side of the base to 3, 5, or T/S to select how long the TAD waits to answer a call (3 rings, 5 rings, or toll-saver). Note: If you plan to check messages by long distance, set RING TIME to toll-sa

For example: 10 “You have reached the Jones residence. We are unable to come to the phone right now, but you may press: 1 to leave a message for John, 2 to leave a message for Mary, 3 to leave a message for Susan, 4 to leave a message for Helen, or you can wait until after the beep to leave a message for John. Please include your name and phone number in your message.” Important: Do not tell callers that you are not home. Instead, say that you cannot come to the phone right now. Follow these ste

If this happens, start over again at Step 1. 1. Press PGM/DEL. The TAD beeps once. illustration 43-781.fm Page 9 Monday, August 16, 1999 7:41 AM 2. Press 1/TIME. The TAD says “Press one for Monday. Press two for Tuesday. Press three for Wednesday. Press four for Thursday. Press five for Friday. Press six for Saturday. Press seven for Sunday.” illustration 3. Press a number button to set the day of the week. The TAD says the day of the week and “Enter the time.” 4. Press two digits for the hour.

DC 9V Jack illustration When you first connect power, the TAD beeps once and the message counter counts up from 0 to 10. Then the TAD beeps. A1, A2, Lo, CL and 0 alternately appear to indicate that no outgoing messages are recorded, and the day/time stamp is not set. 43-786.fm Page 9 Monday, August 16, 1999 8:02 AM On a Wall Plate 1. Plug one end of the supplied short modular cord into the TEL. LINE jack on the top of the TAD. 2. Route the cord into the groove on the phone’s base. 3. Position th

After the new message is played, the PLAY/ SKIP indicator lights. SCREENING CALLS To screen calls, let the TAD-1027 answer them, then listen to the caller’s message through the TAD’s speaker. If you decide to answer the call, pick up any phone on the same phone line as the TAD. The TAD stops recording and resets to answer the next call. Note: If you pick up the phone just as the TAD-1027 answers, the TAD might not stop playing the outgoing message. If this happens, press ANSWER/STOP/DELETE to st

If this happens, return the handset to the base for about 5 seconds. This resets the security access-protection code. • About once a month, fully discharge the battery pack by keeping the handset off the base until the BATT LOW indicator lights. Otherwise, the battery pack loses its ability to fully recharge. • If the BATT LOW indicator does not light, but the phone does not work, recharge the battery pack. (The battery pack charge might be too low to light the indicator.) • If the battery pack