Évaluations - 4, GPA: 4 ( )

Fabricant : Directed Audio Taille : 223.02 kb Nom Fichier : Langue d'enseignement:

The chassis connection point should be scraped free of paint and dirt. Use only quality crimped and/or soldered connectors at both ends of this wire. DO NOT connect this terminal directly to the vehicle battery ground terminal or any other factory ground points. REAR PANEL CONNECTIONS 8 © 2003 Directed Electronics, Inc FIGURE 2—AMPLIFIER CONNECTIONS 250/4 FRONT HIGH INPUT +- L R 1 FRONT HIGH INPUT + - REAR 1 OUTPUT INPUT R L 2 3 L R 7 INPUT 6 3 BASS EQ. OFF ON 5 LPF HPF FLAT MIN MAX 4 GAIN 5 LPF HPF FLAT MIN MAX 4 GAIN 6 BASS EQ. OFF ON FIGURE 2—AMPLIFIER CONNECTIONS 200/2 300/2 REAR 1 2 43 5 FIGURE 2—AMPLIFIER CONNECTIONS 250/4 REAR REMGNDBATT25AFUSELRBRIDGEDSPEAKEROUTPUTFRONTREAR1 2 43 5 © 2003 Directed Electronics, Inc SPEAKER WIRING DIAGRAMS 200/2 300/2 Stereo operation (top view) Mono operation (top view) Simultaneous stereo/mono operation (top view) © 2003 Directed Electronics, Inc SPEAKER WIRING DIAGRAMS 250/4 Stereo Operation (top view) Two Channel Stereo Four Channel Stereo Two Channel Stereo Four Channel Stereo N NNO OOT TTE EE: ::For bridged two channel operation as shown in this diagram, connect right channel RCA cables to the front inputs of the amplifier, and left channel RCA cables to the rear inputs of the amplifier. For summed subwoofer applications, connect RCA cables per the input jack marking. Simultaneous stereo/mono operation (top view) Simultaneous Two Channel Stereo with Mono Sub © 2003 Directed Electronics, Inc CROSSOVER SETTINGS AND GAIN ADJUSTMENT Your Directed Audio power amplifier needs to be adjusted carefully to achieve maximum performance. These are some guidelines to follow when fine-tuning the amplifier. • For full-range and simultaneous stereo/mono bass applications, the crossover selection switch should be set to FLAT. If the amplifier is driving your subwoofers, set the switch to LPF, and for mid-bass/midrange output, set to HPF. • The gain adjustment allows you to set proper signal match for clean, quiet amplifier operation. For full-range and simultaneous stereo/mono bass applications, start by playing some music you are familiar with. With the gain adjustment on the amplifier in the middle of its rotation, bring up the volume on your head unit to the 3/4 volume setting or until you start to hear distortion or clipping. If you hear distortion before you reach the 3/4 volume setting of your head unit, reduce the gain setting on the amplifier and start to raise the head unit volume again. When you can listen to the music at or slightly above 3/4 on your head unit without audible distortion, slowly raise the gain of the amplifier until distortion is heard, then back off the gain until the distortion is not audible. This setting will allow you to reach full output with all but the quietest of source material, while avoiding excessive noise in the system. • The same procedure should be used for adjusting the amplifier when the on-board crossover is set to LPF or HPF, but you will also have to take into consideration the effect that gain adjustment has on system frequency response and imaging. Again, plan on spending some time with music that you know, getting the gain and crossover settings the way you like. Test discs and analyzers may help with this process, but in the end it's your ears that count - listen to the music! © 2003 Directed Electronics, Inc SPECIFICATIONS Directed model 200/2 300/2 250/4 RMS continuous power per channel, both chan50 watts 7 77 5 55 watts 3 33 5 55 watts nels driven into 4 ohms from 20 to 20,000 Hz, x xx 2 22 x xx 2 22 x xx 4 44 with less than 0.08% Total Harmonic Distortion @ 14.4 VDC RMS continuous power per channel, both chan7 77 5 55 watts 1 11 2 22 5 55 watts 5 55 0 00 watts nels driven into 2 ohms from 20 to 20,000 Hz, x xx 2 22 x xx 2 22 x xx 4 44 with less than 0.1% Total Harmonic Distortion @ 14.4 VDC RMS continuous power bridged into a 4 ohm 1 11 5 55 0 00 watts 2 22 5 55 0 00 watts 1 11 0 00 0 00 watts load from 20 to 20,000 Hz, with less than 0.1% x xx 1 11 x xx 1 11 x xx 2 22 Total Harmonic Distortion @ 14.4 VDC Dynamic power rating (IHF-202 Standard) 2 22 0 00 0 00 watts 3 33 0 00 0 00 watts 2 22 5 55 0 00 watts bridged into 4 ohms Signal-to-Noise Ratio Greater than 95 dB Frequency Response 20-20,000 Hz ± 0.5 dB Damping Factor @ 4 ohm Greater than 200 Crossover Switchable high or low pass 12 dB/octave Bass Equalization +8 dB, centered at 40Hz Input Impedance 20K ohms Input Sensitivity Variable from 150 mV to 8 volt Output Impedance 2 to 8 ohms, stereo 4 to 8 ohms, bridged Supply Voltage 10 to 16 VDC Fusing and Power 20A 25A 25A Minimum Cable Requirements (AWG) #12 #10 #10 (Per amp, trunk mounted) © 2003 Directed Electronics, Inc The company behind this system is Directed Electronics, Inc. Since its inception, Directed has had one purpose, to provide customers with the finest vehicle security, car stereo products, rear seat entertainment, and accessories available. The recipient of more than 20 patents in the field of...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :