Évaluations - 2, GPA: 4.5
(
)
)
|
Facilité d'utilisation
16. POWER: Use this switch to turn the amplifier on (top of the switch depressed) or off (bottom of switch depressed). BASS BUS MASTER DSP CD INPUT INSERT POWERLEVEL MODE LEVEL FUNK-WAH FLANGE OCTAVE CHORUS CHO/HALL ECHO ROOM DELAY HALL 9 10 11 13 14 15 1612 BASS BUS MASTER DSP CD INPUT INSERT POWERLEVEL MODE LEVEL FUNK-WAH FLANGE OCTAVE CHORUS CHO/HALL ECHO ROOM DELAY HALL 9 10 11 13 14 15 1612 8 YPP117 DUAL MONO 1/4" TO STEREO 1/4" ADAPTER CA2 1/4" TO RCA ADAPTER STEREO 1/4" TO STEREO 1/4" CABLE TO INSERT, TXB50 TO STANDARD INSERT JACK OF EFFECT (IF EFFECT IS NON-INVERTING) TO INVERTED INSERT JACK OF EFFECT TO MONO OUTPUT JACK OF EFFECT TO MONO INPUT JACK OF EFFECT TO MONO OUTPUT JACK OF EFFECT TO MONO INPUT JACK OF EFFECT TIP: LINE IN (RETURN) RING: LINE OUT (SEND) SLEEVE: GROUND (IF EFFECT IS INVERTING) TO INSERT, TXB50 TO INSERT, TXB50 MONO 1/4" TO MONO 1/4" CABLES RCA TO RCA CABLE STP201, 3' STP202, 6' STP203, 9' DUAL MONO 1/4" TO STEREO 1/4" Y-CABLE RING TO INSERT, TXB50 TO LINE LEVEL OUTPUT OF DEVICE TIP RINGTIP TIP: LINE IN (RETURN) RING: LINE OUT (SEND) SLEEVE: GROUND TIP: LINE IN (RETURN) RING: LINE OUT (SEND) SLEEVE: GROUND ABOUT THE INSERT JACK: The Insert jack (#13) lets you patch external effects into the amplifier just prior to its power amp stage, as shown below. Set the mix controls on the external effects units to “full effect” (100% wet). The Insert jack is a parallel circuit, allowing the connection of another input to the amplifier without interupting the signal from the Input jack. An attenuator or external level control may be needed whenever a line level signal is connected to the Insert jack. Connecting to an effect s insert jack with a stereo cable: Connecting to an effect with a stereo-to-mono Y cable: Connecting to an effect with a stereo-to-mono adapter and cables: Connecting a line level signal into the Insert jack: THE REAR PANEL: 17. DC CHARGER PLUG, 15VDC: Plug the small round connector of the AC wall adapter into this jack to charge the internal battery. The LED next to the jack glows red when the amp is charging. See page 4 for additional information. 18. DC CIGARETTE LIGHTER ADAPTER, 12 VDC: Plug the small round connector of the optional 12-volt car adapter into this jack to play the amplifier from a vehicle, instead of the internal battery. NEVER connect the 15-volt charger to this jack! See page 4 for additional information. DC CIGARETTE LIGHTER ADAPTOR DC CHARGER PLUG 12V DC15V DC LIT WHEN CHARGING POSITIVE NEGATIVE 17 18 YPP117 DUAL MONO 1/4" TO STEREO 1/4" ADAPTER CA2 1/4" TO RCA ADAPTER STEREO 1/4" TO STEREO 1/4" CABLE TO INSERT, TXB50 TO STANDARD INSERT JACK OF EFFECT (IF EFFECT IS NON-INVERTING) TO INVERTED INSERT JACK OF EFFECT TO MONO OUTPUT JACK OF EFFECT TO MONO INPUT JACK OF EFFECT TO MONO OUTPUT JACK OF EFFECT TO MONO INPUT JACK OF EFFECT TIP: LINE IN (RETURN) RING: LINE OUT (SEND) SLEEVE: GROUND (IF EFFECT IS INVERTING) TO INSERT, TXB50 TO INSERT, TXB50 MONO 1/4" TO MONO 1/4" CABLES RCA TO RCA CABLE STP201, 3' STP202, 6' STP203, 9' DUAL MONO 1/4" TO STEREO 1/4" Y-CABLE RING TO INSERT, TXB50 TO LINE LEVEL OUTPUT OF DEVICE TIP RINGTIP TIP: LINE IN (RETURN) RING: LINE OUT (SEND) SLEEVE: GROUND TIP: LINE IN (RETURN) RING: LINE OUT (SEND) SLEEVE: GROUND ABOUT THE INSERT JACK: The Insert jack (#13) lets you patch external effects into the amplifier just prior to its power amp stage, as shown below. Set the mix controls on the external effects units to “full effect” (100% wet). The Insert jack is a parallel circuit, allowing the connection of another input to the amplifier without interupting the signal from the Input jack. An attenuator or external level control may be needed whenever a line level signal is connected to the Insert jack. Connecting to an effect s insert jack with a stereo cable: Connecting to an effect with a stereo-to-mono Y cable: Connecting to an effect with a stereo-to-mono adapter and cables: Connecting a line level signal into the Insert jack: THE REAR PANEL: 17. DC CHARGER PLUG, 15VDC: Plug the small round connector of the AC wall adapter into this jack to charge the internal battery. The LED next to the jack glows red when the amp is charging. See page 4 for additional information. 18. DC CIGARETTE LIGHTER ADAPTER, 12 VDC: Plug the small round connector of the optional 12-volt car adapter into this jack to play the amplifier from a vehicle, instead of the internal battery. NEVER connect the 15-volt charger to this jack! See page 4 for additional information. DC CIGARETTE LIGHTER ADAPTOR DC CHARGER PLUG 12V DC15V DC LIT WHEN CHARGING POSITIVE NEGATIVE 17 18 SUGGESTED SET-UPS: The TXB50 can be used in a variety of different ways, some of which are shown below and on the following page. Use these ideas to fuel your imagination for the setup which best suits your needs. Idea 1 – Play along, with external effects and backup: Connect an instrument (bass, guitar, keyboard) to the Input jack. (This high-Z input works with all types of pickups, fr...