Évaluations - 2, GPA: 4
(
)
)
|
Facilité d'utilisation
• Do not allow the wire to directly contact the edge of the iron plate by using Grommets. • Connect the ground wire to a metal part of the car chassis that acts as an electrical ground passing electricity to the battery‘s negative - terminal. Do not turn the power on if the ground wire is not connected. • Be sure to install a protective fuse in the power cord near the battery. The protective fuse should be the same capacity as the unit’s fuse capacity or somewhat larger. • For the power cord and ground, use a vehicle type (fireproof ) power wring cord with a current capacity greater than the unit’s fuse capacity. (Use a power wiring cord with a diameter of 5 mm. (AWG 10) or greater.) • When more than one power amplifier are going to be used, use a power supply wiring wire and protective fuse of greater current-handling capacity than the total maximum current drawn by each amplifier. ¦ Speaker selection • The input power of the speakers that are going to be connected should be greater than the output power (in Watts) of the amplifier. Use of speakers having input power ratings that are less than the output power of the amplifier will cause smoke to be emitted as well as damage. • The impedance of the speakers that are going to be connected should be 2. or greater (for stereo connections), or 4. or greater (for bridged connections). When more than one set of speakers are going to be used, calculate the combined impedance of the speakers and then connect suitable speakers to the amplifier. 4. 4. 4. 4. 2. 8. Combined impedance English 5 6 English Connection CENTER UNIT (CD receiver, etc.) A channel input RCA cable* Power control wire (Blue/ White) ¦ RCA cable or Speaker level input connection Genuine-accessory car stereo (No line output center unit etc.) ACC Battery Car fuse box • RCA cable connections • Speaker level input connections B channel input Speaker level input cable NOTE • Do not connect cables and leads to both RCA cable input jacks and the speaker level input terminals simultaneously, for this may cause malfunction or damage. Speaker level input terminals • The genuine-accessory car stereo shall have a maximum power output of no more than 40 W. • Connect the power control lead to a power supply which can be turned ON/OFF by the ignition key switch (ACC line). With this connection, pop noise may be generated when the power of the genuine-accessory car stereo is switched ON/OFF. Speaker output terminals (A.ch/ B.ch) • Stereo Connections: The speakers to be connected should have an impedance of 2. or greater. When multiple speakers are to be connected, ensure that the combined impedance is 2. or greater for each channel. • Bridged Connections: Make connections to the LEFT channel 9 and the RIGHT channel · SPEAKER OUTPUT terminals. The speakers to be connected should have an impedance of 4. or greater. When multiple speakers are to be connected, ensure that the combined impedance is 4. or greater. Power control terminal Controls the unit ON/OFF. NOTE Controls the unit power. Be sure to connect it with all the systems. Fuse KAC-M845: 40 A . 1 KAC-M645: 25 A . 1 Cable Color of the connector A channel Left 9 White · White/Black A channel Right 9 Gray · Gray/Black B channel Left 9 Green · Green/Black B channel Right 9 Purple · Purple/Black English 7 * Commercially available parts .. ¦ Speaker wire connection Lead terminal* • Stereo Connections A channel Left speaker A channel Right speaker • Bridged Connections A channel Speaker (Bridged) 40 25 Battery Battery wire* Ground wire* Protective Fuse* Lead terminal* ¦ Power wire connection Terminal cover B channel Left speaker B channel Right speaker B channel Speaker (Bridged) Power control wire* KAC-M645 KAC-M845 Troubleshooting Guide What might appear to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems. PROBLEM POSSIBLE CAUSE SOLUTION No sound. (No sound from one side.) (Blown fuse.) The output level is too small (or too large). The sound quality is bad. (The sound is distorted.) • Input (or output) cables are disconnected. • Protection circuit may be activated. • Volume is too high. • The speaker cord is shorted. • The input sensitivity adjusting control is not set to the correct position. • The speakers wire are connected with wrong 9 / · polarity. • A speaker wire is pinched by a screw in the car body. • The switches may be set improperly. • Connect the input (or output) cables. • Check connections by referring to
Avtousiliteli - KAC-M845 (695.83 kb)