Introduction...................................................................................... 3 1.1 Features .................................................................................... 4 1.2 About Installation ...................................................................... 4 2. Installation and use.......................................................................... 5 3. System Design with the GTH400..................................................... 6 3.1 Speaker Req

Be sure to use appropriate grommets whenever routing wires through the firewall or other sheet metal. Failure to adequately protect the positive wire from potential damage may result in a vehicle fire. When you are done routing and connecting this wire, you may install the fuse at the battery. NOTE: The BPx2200.1 is supplied with an external 150A fuse. If you are running a dedicated wire to this amplifier, this fuse should be installed near the battery, as specified above. If you are running mul

The JBL Px600.2 amplifier is set to stereo mode to drive a pair of full-range speakers. Figure 5. The JBL Px600.2 amplifier is set to bridged (mono) mode to drive a single subwoofer. Use this mode only when the nominal impedance of the subwoofer is 4 ohms or greater. 4 APPLICATIONS – Px600.2 The JBL Px600.2 amplifier can be set up for stereo or bridged-mono operation, as shown in Figures 4 and 5. NOTE: For simplicity, Figures 4 and 5 do not show power, remote and input connections. APPLICATIONS

6. Route each neon tube’s power cable through its respective NEON hole on the end panel (see Figure 9). 7. Slide the cover back into place and reinstall its screws. Then, replace the end panel and reinstall its screws. 8. Finish the installation of the neon tubes as instructed in their owner’s manual. POWERFUSESGNDREMBATTSPEAKEROUTPUTSBRIDGEDSTEREOPx600.2LRNEONNEONPROTECTPOWERI-E OPTInstalling A Clip On Extrusion Lip (side view) ClipNeonTubeNeon Tube and ClipLipInstalled Neon Tube Under Extrusio

• At the installation sites, locate and make a note of all fuel lines, hydraulic brake lines, vacuum lines and electrical wiring. Use extreme caution when cutting or drilling in and around these areas. • Choose a safe mounting location away from moisture. • Make sure there is sufficient air circulation at the mounting location for the amplifier to cool itself. • Mount the amplifier, using the supplied hardware. Specifications • 40W RMS x 2 @ 4 ohms and .1% THD + N* • 60W RMS x 2 @ 2 ohms, 14.4V

Figure 4. CS50.4 amplifier in 4-channel (stereo) operation to drive front and rear full-range speakers. Figure 5. CS50.4 is set up for 3-channel operation to drive a set of full-range speakers and a subwoofer. Figure 6. CS50.4 used in bridged 2-channel mode to drive a set of components or subwoofers. Set crossovers according to application. APPLICATIONS – CS50.4 The CS50.4 can be set up for stereo 4-channel, 3-channel or bridged 2-channel operation, as shown in Figures 4 through 6. NOTE: For sim

Luxembourg, Mendriso Branch 3 Moree St., CH 6850 Mendrisio Switzerland р г Front/Rear view 1 i H J M 71 ij 0j J 2 <> DO^DP HJFT ""\ *** N s* REN m — . t % c Q=D(Mll @01= ■CH (u! (u) »™ Ml IE 1 32 u O -± oN) +12V GND REM E Low Level Input Fuse K Gain Controll E 12V (DC) power terminal E Low pass switch ¿6 Remote terminal Low pass cutting adjustment GND terminal S Multiplayer x1/x10 switch for Low section + Left channel terminal (+ MONO) S'

Part No. GTOAMPOM1/04 JBL Consumer Products

Failure to adequately protect the positive wire from potential damage may result in a vehicle fire. When you are done routing and connecting this wire, you may install the fuse at the battery. Remote Connection Connect the amplifier’s Remote (REM) terminal to the source unit’s Remote Turn- On lead using a minimum of 18-gauge wire. NOTE: When using the speaker level inputs, connect the remote (REM) terminal to the source unit. If your source unit does not have a remote turn-on connection, connect

Set both parts aside. 4. Locate the enclosed hardware bag and remove the four clips. Each clip has a square end and a larger round end. Using a round end, press two clips onto each neon tube (e.g., Street Glow AN9 or equivalent), as shown in Figure 13. 5. For each tube, align both clips so the square ends slide onto an exposed extrusion edge, as shown in Figure 9. Do not cover any screw holes. When installed correctly, each neon tube will sit under an extrusion and not be visible when viewed fro