It is highly recommended that installation be carried out by an authorized MTX dealer. MODEL # FUSE MODEL # FUSE TC6004 75A TC8001 90A TC4004 60A TC6001 60A TC4002 50A TC4001 40A TC3002 40A TC3001 30A TC2002 25A 2. Connect the amplifier remote turn-on Connect the remote input terminal of the amplifi er to the remote output terminal of the source unit (only if using RCA inputs) to establish amplifi er remote on/off through the power on/off of the source unit. If a source unit is being used withou

Ground: 10 AWG. Remove Paint -From Metal ForjnslajlatjonoptionsgoJomtxçvm.

Ground: 10 AWG. Remove Paint -From Metal ForjnslajlatjonoptionsgoJomtxçvm.

on your purchase of a new MTX Audio Thunder Amplifier! MTX has long been the industry leader in mobile enclosures and speakers, and we have reached new heights with the development of the new MTX Thunder amplifiers. You couldn’t have chosen a more reliable, powerful, or better performing amplifier. In fact, we back up every Thunder amplifier with a three-year warranty if installed by an authorized MTX Audio retailer (see the warranty statement). Your new MTX Thunder amplifier was designed, built

With this setting, the Remote Gain can directly control the amplifi er playback level. 3. When the full range is selected (FR), the amplifi er is used as a full range amplifi er. CROSSOVER FREQUENCY SELECTION (FREQ) Both the high-pass and the low-pass section offer continuously adjustable crossover frequencies between 40Hz and 350Hz. Adjust the setting according to your speaker component specifi cation or to your particular preference. BASS BOOST CONTROl (BASS BOOST) Select a boost level between

Do not connect to Factory bolts of ANY kind. When attaching the ground to the chassis, sand all the paint away from the contact point, a grounding block like the StreetWires GT4 should be used whenever possible, this piece of equipment has 5 times the surface area a normal screw has. The gauge of the power and ground wire is often an overlooked aspect of amplifier installation. The more power the amplifier receives, the more power it will produce. Power cables have a natural resistance, and will

Securely mount the amplifier. If everything is in order, reconnect the vehicles negative battery connection and begin following the feature setup and adjustment steps. Feature Setup and Adjustments 1. Selecting The Input Sensitivity Range – Before you turn on your system, you must select the proper input sensitivity range on your amp using the button labeled INPUT SENS located in the GAIN CONTROL section of the control panel. • Setting for aftermarket Source Units: Refer to your aftermarket owne

Normal source units can only keep a constant 12 volts to 2 or possibly 3 amps. This wire should also be run on the away from RCA cables. • CAP+: This 8 gauge terminal is internally wired in parallel with the +12V on the StreetWires Power connector. It is the ideal connection point for the positive side of a capacitor to increase the amplifier’s performance. • CAP-: This 8 gauge terminal is internally wired in parallel with the GND on the StreetWires Power connector. It is the ideal connection po

Adding MTX amplifiers and matching MTX speakers and subwoofers with StreetWires connections will put you in a better position to hear, feel, and experience all of the music the artist intended. Specifications Primary Ratings: Power Output: 250 watts RMS x 1-channel at 4 ohm and . 1% THD+N Signal-to-Noise Ratio (1 watt): 71dB Secondary Ratings Power Output: 500 watts RMS x 1-channel at 2 ohm and . 1% THD+N THD+Noise (Distortion) (1 watt): . .5% Frequency Response (-3dB): 20Hz-200Hz Maximum Input

If the specification is not available, please follow the instructions listed below. X1 POSITION: 100mV–1V (Typically for RCA Input) • Setting for Factory (OEM) Source Units: To check the amount of voltage that is present from the source unit, take a multi meter, or a volt/ohm meter, on the A/C setting, (range from 100mV up to 10 volts) attach the positive and negative leads directly to any exposed speaker. It will not matter if the polarity is correct, it will read the same amount of voltage. X