For example, in Figure 4, each woofer you should design a speaker system will have an impedance of 12 ohms, by based on the RMS power handling of The JBL A6000GTi and A3000GTi your speakers. For music with sharp Ztotal = Z1 + Z2 = 6 + 6 = 12 amplifiers support a wide range of transient bass notes (e.g., rock, and the three woofers connected country or jazz), the RMS power impedances, and any speaker system in parallel will have an equivalent handling rating is conservative, and with a total or e

When the cover is removed, the amplifier will turn off and speaker connections can be made safely. Use 0-gauge cable to connect the BATT+ terminal directly to the vehicle’s battery. If the battery is located in the engine compartment and the BATT+ cable must be routed through the firewall or any metal obstruction, install a wafer-type (ANN) fuse with a current rating of at least 500 amperes and an appropriate fuse holder within 18" of the vehicle’s battery (see Figure 5). 1 = Battery Voltage (to

The JBL Px600.2 amplifier is set to stereo mode to drive a pair of full-range speakers. Figure 5. The JBL Px600.2 amplifier is set to bridged (mono) mode to drive a single subwoofer. Use this mode only when the nominal impedance of the subwoofer is 4 ohms or greater. 4 APPLICATIONS – Px600.2 The JBL Px600.2 amplifier can be set up for stereo or bridged-mono operation, as shown in Figures 4 and 5. NOTE: For simplicity, Figures 4 and 5 do not show power, remote and input connections. APPLICATIONS

6. Route each neon tube’s power cable through its respective NEON hole on the end panel (see Figure 9). 7. Slide the cover back into place and reinstall its screws. Then, replace the end panel and reinstall its screws. 8. Finish the installation of the neon tubes as instructed in their owner’s manual. POWERFUSESGNDREMBATTSPEAKEROUTPUTSBRIDGEDSTEREOPx600.2LRNEONNEONPROTECTPOWERI-E OPTInstalling A Clip On Extrusion Lip (side view) ClipNeonTubeNeon Tube and ClipLipInstalled Neon Tube Under Extrusio

Be sure to use appropriate grommets whenever routing wires through the firewall or other sheet metal. Failure to adequately protect the positive wire from potential damage may result in a vehicle fire. When you are done routing and connecting this wire, you may install the fuse at the battery. NOTE: The BPx2200.1 is supplied with an external 150A fuse. If you are running a dedicated wire to this amplifier, this fuse should be installed near the battery, as specified above. If you are running mul

Figure 4. CS50.4 amplifier in 4-channel (stereo) operation to drive front and rear full-range speakers. Figure 5. CS50.4 is set up for 3-channel operation to drive a set of full-range speakers and a subwoofer. Figure 6. CS50.4 used in bridged 2-channel mode to drive a set of components or subwoofers. Set crossovers according to application. APPLICATIONS – CS50.4 The CS50.4 can be set up for stereo 4-channel, 3-channel or bridged 2-channel operation, as shown in Figures 4 through 6. NOTE: For sim

INSTALLATION 2 THANK YOU for purchasing a JBL CS Series amplifier. In order that we may better serve you should you require warranty service for your new amplifier, please retain your original purchase receipt and register your new JBL amplifier online at WARNING Playing loud music in an automobile can hinder your ability to hear traffic and permanently damage your hearing. We recommend listening at low or moderate levels while driving your car. JBL accepts no liability for hearing loss, bodily

There are two sets of terminals to make it easy to connect multiple woofers. Either set of (+/–) terminals may be used when connecting woofers. To the right are two application diagrams to help plan your subwoofer system installation. Figures 4 and 5 show how to configure the CS300.1 subwoofer amplifier. NOTE: For simplicity, Figures 4 and 5 do not show power, remote and input connections. NOTE: Minimum speaker load is 2 ohms total. Figure 4. CS subwoofer amplifier with two woofers connected. Fi

Instead, please ask your authorized JBL car audio dealer about professional installation. INSTALLATION CHOOSING A LOCATION WARNINGS AND TIPS AND MOUNTING THE • Always wear protective eyewear when using tools. • Turn off the audio system and other electrical devices before you start. Disconnect the (–) negative lead from your vehicle’s battery. • At the installation sites, locate and make a note of all fuel lines, hydraulic brake lines, vacuum lines and electrical wiring. Use extreme caution when

Either + or -terminal may be used. Minimum total impedance is 1 ohm. © Fuses • Replace only with the same type and rating. © Power Input Connectors • +12V: Connect to the positive terminal of the vehicle's battery. 8 AWG wire is recommended. Install an appropriate fuse holder and fuse (40A minimum) within 18 inches of the battery. Make sure the wire is not damaged or pinched during installation. Install protective grommets when routing wires through the firewall or other sheet metal. • GND: