Évaluations - 4, GPA: 3.5
(
)
)
|
Facilité d'utilisation
(The illustrations are as viewing the deck from above with the Ladder to be installed on the left side.) 15’ END DECK & 18’ END DECK POOL POOL Having positioned the Bottom Support Channels in their proper locations as illustrated above, attach them to the bottom of the Posts (including the Post for the Ladder) using 1/2” Sheet Metal Screws as shown at right. 73-3/4” 58-7/8” 58-7/8” 12’ END DECK ""I 73-3/4” 1 BOTTOM SUPPORT CHANNEL 1/2” SHEET METAL SCREW BOTTOM OF POST NOTE: On the 12’ End Deck, you must now attach 1 side of remaining 72^” Bottom Support Channel to the outside Posts nearest the pool. See right. 6 12’ END DECK ^-52-5/16-► 15’ END DECK M- 66-3/4 -► 18’ END DECK *-79-7/16-► IMPORTANT: ONLY HAND TIGHTEN SCREWS AT THIS TIME Where the Posts and the Bottom Support Channels join, attach Angle Support Bars. The illustrations below indicate Close-up illustrations show the proper assembly procedure for each location. Where One Angle Support Bar attach to the Post use the V” Sheet Metal Screws. Where Two Angle Support Bars attach to the Post use the 1” Sheet Metal Screw. Where the Angle Support Bars attach to the Bottom Support Channels use the V” Truss Head Screws and Hex Nuts. Note carefully in the Close-ups the position of the slots in the Angle Support Bars. Again, only hand tighten screws at this time. CLOSE-UP #7 CLOSE-UP #7 CLOSE-UP #7 POOL CLOSE-UP #7 15’ END DECK & 18’ END DECK CLOSE-UP #7 CLOSE-UP #7 □ CLOSE-UP #7 □ CLOSE-UP #8 Q CLOSE-UP #7 CLOSE UP #7 POOL BOTTOM SUPPORT CHANNEL CLOSE-UP #7 □ 12’ END DECK CLOSE-UP #7 ANGLE SUPPORT BAR CLOSE UP #8 BOTTOM SUPPORT CHANNEL BOTTOM OF POST 1” SHEET METAL SCREW 1/4” x 20 1/4” x 20x1/2” 1/2” SHEET 1” SHEET HEX NUT TRUSS HEAD SCREW METAL SCREW METAL SCREW 7 IMPORTANT: ONLY HAND TIGHTEN SCREWS AT THIS TIME Where the Posts fasten to the deck, attach Angle Support Bars. The illustrations below indicate which of the Close-up illustrations at the bottom of this page and at the top of the next page show the proper assembly procedure for each location. Where One Angle Support Bar attach to the Post use the 1^” Sheet Metal Screws. Where Two Angle Support Bars attach to the Post use the 1” Sheet Metal Screw. Where the Angle Support Bars attach to the deck use the M-” Truss Head Screws and Hex Nuts. CLOSE-UP #13 □ CLOSE-UP #13 /\ CLOSE-UP #11 Q CLOSE-UP #10 CLOSE-UP #13 □ 15’ END DECK & 18’ END DECK CLOSE-UP #10 POOL CLOSE-UP #13 □ CLOSE-UP #11 Q CLOSE-UP #13 CLOSE-UP #10 CLOSE UP #10 POOL CLOSE-UP #13 □ 12’ END DECK $tww> 1/4” x 20 1/4” x 20x1/2” 1/2” SHEET 1” SHEET HEX NUT TRUSS HEAD SCREW METAL SCREW METAL SCREW 8 CLOSE UP #13 0 IMPORTANT: ONLY HAND TIGHTEN SCREWS AT THIS TIME For the 15’ and 18’ Decks assemble the Center Patio to the already assembled deck sections using the 1” Round Head Screws and Hex Nuts. For the 12’ Decks assemble the two outside deck sections together using the 1” Round Head Screws and Hex Nuts. Firmly tighten these screws. Next, attach the Left Patio and Right Patio sections in the same manner, firmly tightening the screws (let all other screws remain loose at this time). For all size decks: At the two places labeled “Location A” in the illustration above, attach Long Square Posts in the manner illustrated at right in Close-up #15. For the 18’ Decks only: At the two places labeled “Location B” in the illustration above, also attach Long Square Posts in the manner illustrated at right in Close-up #15. 9 1/4” x 20 x 2” TRUSS HEAD SCREW 1/4” x 20 HEX NUT 1/4” x 20 x 1/2” ROUND HEAD SCREW . o IMPORTANT: ONLY HAND TIGHTEN SCREWS AT THIS TIME 18’ END 15’ END DECK BOTTOM SUPPORT CHANNEL 1/2” SHEET METAL SCREW fa "N 1/2” SHEET METAL SCREW BOTTOM OF POST 12’ END DECK For the 12’ End Deck attach the two 75” Bottom Angles to the bottom of the Posts as shown. Use 1/2” Sheet Metal Screws but only hand tighten at this time. 10 In the locations marked “Location A” (see the previous page), attach Angle Support Bars to the top of the Post and Deck as illustrated in Close-up #16 at right. Also attach Angle Support Bars to the bottom of the Post and the Bottom Support Channel as illustrated in Close-up #17 at right. Note: Where One Angle Support Bar attach to the Post use the M>” Sheet Metal Screws. Where Two Angle Support Bars attach to the Post use the 1” Sheet Metal Screw. Where they attach to either the deck or the Bottom Support Channels. CLOSE UP #17 1/4” x 20 HEX NUT 1/4” x 20 x 1/2” TRUSS HEAD SCREW 1/2” SHEET METAL SCREW In the locations marked “Location C” (see the previous page), attach 49-5/16” Posts to the Deck as illustrated in Close-up #4 at right. Also attach Angle Support Bars to the top of the Posts and the deck as illustrated in Close-up #12 at right. Note: Where One Angle Support Bar attach to the Post use the M>” Sheet Metal Screws. Where Two Angle Support Bars attach to the Post use the 1” Sheet Metal Screw. Whe...