Évaluations - 4, GPA: 3
(
)
)
|
Facilité d'utilisation
8.3 Remove starter cord shield screws. 8.4 Relieve spring tension. A Pull 4-6” of rope out. B Line rope up with notch on pulley. C Slowly rotate pulley counterclockwise until spring pressure is released. Use thumb as a brake. 8.5 Remove starter pulley screw and washer. NOTE: Hold starter cover firmly. F/N 71537 Oct 07 © 2007 ICS, Blount Inc. TITLE 8. STARTER TITLE 8. STARTER 613GC SERVICE MANUAL 8.6 Remove starter pulley. 8.7 Inspect coil spring. A Replace if spring hook is damaged. Attempting to re-bend the spring hook may cause the hook to break off. B Carefully remove coil spring and housing to prevent spring from unwinding. 8.8 Lubricate with light weight oil. 8.9 Replace parts carefully. © 2007 ICS, Blount Inc. F/N 71537 Oct 07 TITLE 8. STARTER TITLE 8. STARTER 613GC SERVICE MANUAL 8.10 Inspect pulley spring catch. A Clean with cleaning solution. B Replace if worn or broken. 8.11 Install starter rope and tie knot. 8.12 Install pulley A Wind rope onto pulley clockwise leaving 4-6” out. B Make sure that the pulley spring catch is in the spring hook. 8.13 Install center screw. A Use blue Loctite®. BTorque to 26 in-lbs. (2.9 Nm). F/N 71537 Oct 07 © 2007 ICS, Blount Inc. TITLE 8. STARTER TITLE 8. STARTER 613GC SERVICE MANUAL 8.14 Wind the recoil spring. A Line rope up with notch on pulley. B Rotate the pulley with the rope clockwise 5 times. C Untangle rope and release. 8.15 Assemble starter cord shield. 8.16 Remove starter pawl screws, pawls, spring, and plain washer. 8.17 Inspect and clean pawl components. A Inspect the components. Replace if necessary. B Clean the components with a brush and solvent. © 2007 ICS, Blount Inc. F/N 71537 Oct 07 613GC SERVICE MANUAL TITLE 8. STARTER 8.18 Assemble components A Make sure the spring is in the correct position. B Use blue Loctite® on the pawl screws. CTorque to 60 in-lbs. (6.8 Nm). 8.19 Wind the pawl spring. A Use needle nose pliers to move the tail of the spring into position. 8.20 Install starter cover. A Pull out cord 4-6”. B Slowly release while placing cover to allow pawls to engage. F/N 71537 Oct 07 © 2007 ICS, Blount Inc. TITLE 8. STARTER TITLE 8. STARTER 613GC SERVICE MANUAL 8.21 Install starter cover screws. A Use blue Loctite® . B Torque to 60 in-lbs. (7 Nm). © 2007 ICS, Blount Inc. F/N 71537 Oct 07 613GC SERVICE MANUAL TITLE 9. WALLWALKER 9 This section covers the removal, inspection, and assembly of the WallWalker® and guard flap. 9.1 Inspect WallWalker® tip. A If the tip is worn, as shown, replace. 9.2 Remove crankcase screws and wave washers. 9.3 Remove WallWalker® from saw. NOTE: On late model saws it is necessary to remove the bar plate prior to removing the crankcase screws. 9.4 Remove guard flap screws and washer. 9.5 Remove and inspect guard flap. A Replace the flap if it is torn or damaged in any way. F/N 71537 Oct 07 © 2007 ICS, Blount Inc. TITLE 9. WALLWALKER TITLE 9. WALLWALKER 613GC SERVICE MANUAL 9.6 Reassemble in the reverse order. A Install crankcase screws and wave washers. B Use blue Loctite® . C Torque to 70 in-lbs. (7.9 Nm). © 2007 ICS, Blount Inc. F/N 71537 Oct 07 613GC SERVICE MANUAL TITLE 10. CYLINDER COVER 10 This section covers the disassembly and assembly of the cylinder cover. Removal of the air intake components and front handle is necessary. Refer to sections 1 and 14 if needed. 10.1 Remove the air filter mount screws. 10.2 Remove the cylinder cover screws (3). 10.3 Remove spark plug lead from cylinder cover. 10.4 Remove fuel tank breather cap and clamp. 10.5 Partially remove intake manifold from cylinder cover. 10.6 Remove cylinder cover. A Pull up on front. B Push intake manifold through hole. C Make sure throttle linkage is disengaged from cylinder cover. D Guide fuel breather tube and compensator tube through cylinder cover. F/N 71537 Oct 07 © 2007 ICS, Blount Inc. TITLE 10. CYLINDER COVER TITLE 10. CYLINDER COVER 613GC SERVICE MANUAL 10.7 Remove stop switch leads. 10.8 Inspect cylinder cover for damage. A Replace if necessary. 10.9 Check cylinder cover water seal and filter cover gasket are in place and in good condition. A Replace if necessary. 10.10 Reassemble stop switch leads. 10.11 Make sure carburetor screw boot is in place. 10.12 Lubricate compensating tube and fuel tank breather tube with soapy water, guide through cylinder cover (Install compensating tube first). NOTE: Be careful as to not pull tubes away from their point of connection. Approximately 3/4” of tube should protrude from cylinder cover. © 2007 ICS, Blount Inc. F/N 71537 Oct 07 613GC SERVICE MANUAL TITLE 10. CYLINDER COVER 10.13 Install cylinder cover. A Pull spark plug lead into slot in cylinder cover. B Align throttle linkage with cylinder cover and crankcase. C Push the cylinder cover down on the crankcase, guide intake manifold into cylinder cover. D Install the cylinder cover screws. Use blue Loctite®. Torque to 35 in-lbs. (4.0 Nm). E Install fuel tank breather and clamp. 10.14 Install air filter mount. A Guide carburetor compensating tube thr...
Ce manuel est également adapté pour les modèles :Benzo et scies - ICS 613GC (4.44 mb)
Benzo et scies - ICS 613GC (4.44 mb)