Évaluations - 4, GPA: 3.8
(
)
)
|
Facilité d'utilisation
. BACKWARD SLOPE - Needs too much feed pressure, causes excessive wear to bar and chain. Results from using a file with diameter too large, or file held too high. Depth Gauge Clearance See Figure 36 - 38. . The depth gauge should be maintained at a clearance of .025 in. Use a depth gauge tool for checking the depth gauge clearances. . Every time the chain is filed, check the depth gauge clearance. Use a flat file and a depth gauge jointer to lower all gauges uniformly. Depth gauge jointers are available in .020 in. to .035 in. Use a .025 in. depth gauge jointer. After lowering each depth gauge, restore original shape by rounding the front. Be careful not to damage adjoining drive links with the edge of the file. Depth gauges must be adjusted with the flat file in the same direction the adjoining cutter was filed with the round file. Use care not to contact cutter face with flat file when adjusting depth gauges. MAINTENANCE INcorrecT TOP PLATE FILING ANGLE correcT TOP PLATE FILING ANGLE LESS THAN 30° MORE THAN 30° 30° Fig. 34 INcorrect SIDE PLATE FILING ANGLE correct SIDE PLATE FILING ANGLE HOOK BACKWARD SLOPE 80° Fig. 35 raker clearance .025 in. Fig. 36 GUIDE BAR MAINTENANCE See Figure 39. When the guide bar shows signs of wear, reverse it on the saw to distribute the wear for maximum bar life. The bar should be cleaned every day of use and checked for wear and damage. Feathering or burring of the bar rails is a normal process of bar wear. Such faults should be smoothed with a file as soon as they occur. A bar with any of the following faults should be replaced. . Wear inside the bar rails which permits the chain to lay over sideways. . Bent guide bar. . Cracked or broken rails. . Spread rails. In addition, guide bars with a sprocket at their tip must be lubricated weekly with a grease syringe to extend the guide bar life. Using a grease syringe, lubricate weekly in the lubricating hole. Turn the guide bar and check that the lubrication holes and chain groove are free from impurities. TRANSPORTING AND STORING See Figure 40. . Do not store or transport the chain saw when it is running. The chain saw should always be idle before storing or transporting. . Always place the guide bar scabbard on the bar and chain before storing or transporting the chain saw. Use caution to avoid the sharp teeth of the chain. . Clean the chain saw thoroughly before storing. Store the chain saw indoors, in a dry place that is locked and/or inaccessible to children. . Keep away from corrosive agents such as garden chemicals and de-icing salts. MAINTENANCE DEPTH GAUGE JOINTER FLAT FILE Fig. 37 RESTORE ORIGINAL SHAPE BY rounding the front Fig. 38 LUBRICATING HOLE Fig. 39 Fig. 40 TROUBLESHOOTING Problem Cause Solution 1. Tension chain. Refer to Chain Tension earlier in this manual. 2. Check oil tank. 1. Retension chain, Refer to Chain Tension earlier in this manual. 2. Refer to Assembling the Bar and Chain earlier in this manual. 3. Inspect guide bar and chain for damage. 1. Check chain tension for over tight condition 2. Chain oil tank empty. 1. Chain tension too tight. 2. Check guide bar and chain assembly. 3. Check guide bar and chain for damage. Bar and chain running hot and smoking. Motor runs, but chain is not rotating. CALL US FIRST For any questions about operating or maintaining your product, call the Ryobi® Help Line! Your product has been fully tested prior to shipment to ensure your complete satisfaction. WARRANTY LIMITED WARRANTY STATEMENT Techtronic Industries North America, Inc., warrants to the original retail purchaser that this Ryobi® brand outdoor product is free from defect in material and workmanship and agrees to repair or replace, at Techtronic Industries North America, Inc.’s, discretion, any defective product free of charge within these time periods from the date of purchase. .. Two years if the product is used for personal, family or household use; .. 90 days, if used for any other purpose, such as commercial or rental. This warranty extends to the original retail purchaser only and commences on the date of the original retail purchase. Any part of this product found in the reasonable judgment of Techtronic Industries North America, Inc. to be defective in material or workmanship will be repaired or replaced without charge for parts and labor by an authorized service center for RYOBI® brand outdoor products (Authorized Ryobi Service Center). The product, including any defective part, must be returned to an authorized Ryobi service center within the warranty period. The expense of delivering the product to the service center for warranty work and the expense of returning it back to the owner after repair or replacement will be paid by the owner. Techtronic Industries North America, Inc.’s, responsibility in respect to claims is limited to making the required repairs or replacements and no claim of breach of warranty shall be cause for cancellation or rescission of the contract of sale of any Ryobi® brand outd...