Évaluations - 3, GPA: 3.7
(
)
)
|
Facilité d'utilisation
part no. 15" (38 cm) 3/8" 443 038 651 522 094 656 18" (45 cm) 3/8" 443 045 651 522 094 664 21" (53 cm) 3/8" 443 053 651 522 094 672 Drive link gauge: .058", Chain sprocket: 7 teeth PUTTING INTO OPERATION Mounting the guide bar and saw chain Use the universal wrench delivered with the chain saw for the CAUTION: following work. Put the chain saw on a stable surface and carry out the following steps for mounting the guide bar and chain: CAUTION: STOP Before doing any work on the guide bar or chain, always switch off the engine and pull the plug cap off the spark plug (see "Replacing the spark plug"). Always wear protective gloves! Start the chain saw only after having assembled it completely and inspected! A 2 1 B 4 3 -Always release the chain brake before removing or replac- Unscrew retaining nuts (B/3). ing the sprocket guard (B/4). To do so, pull the hand guard -Pull off the sprocket guard (B/4). (A/1) towards the tubular handle (A/2) until you feel it catch. C 6 7 D 8 -Turn the chain adjusting screw (C/6) to the left (counter- Position the guide bar (D/8). Make sure that the pin (C/7) clockwise) until the pin (C/7) is at the left stop. of the chain tightener is in the hole (circled) on the guide bar. E 10 9 F 9 11 -Lift the chain (E/9) over the clutch drum and onto the -Lead the chain (F/9) around the sprocket nose (F/11) of sprocket (E/10). Using your right hand, guide the chain into the guide bar. the top guide groove on the guide bar (D/8). Note that the NOTE: The chain should be easy to pull in the direction of the cutting edges along the top of the chain must point in the arrow. The clutch drum (E/10) should turn with the chain (the direction of the arrow! sprocket engages the chain). G H 34 G H 34 -Turn the chain tightener (C/6) to the right (clockwise) until the chain engages the guide groove of the bottom side of the bar (see circle). Press the guide bar against the housing with your left hand. Tightening the saw chain I -Slightly lift the end of the guide bar and turn the chain adjusting screw (C/6) to the right (clockwise) until the chain rests against the bottom side of the guide bar. -While still holding up the tip of the guide bar, tighten the retaining nuts (H/3) with the universal wrench. Chain brake -Replace the sprocket guard (H/4). -Manually tighten the retaining nuts (H/3). Checking the chain tension STOP J -The tension of the chain is correct if the chain rests against the bottom side of the guide bar and can still be easily turned by hand. -While doing so the chain brake must be released. -Check the chain tension frequently - new chains tend to get longer during use! -When checking the chain tension the engine must be switched off. NOTE: It is recommended to use 2-3 chains alternatively. In order to guarantee uniform wear of the guide bar the bar should be turned over whenever replacing the chain. K L 3 1 2 The MAKITA models comes with an inertia chain brake as standard equipment. If kickback occurs due to contact of the guide-bar tip with wood (see SAFETY PRECAUTIONS), the chain brake will stop the chain through inertia if the kickback is sufficiently strong. The chain will stop within a fraction of a second. The chain brake is installed to block the saw chain before starting it and to stop it immediately in case of an emergency. Engaging the chain brake (braking) If the kickback is strong enough the sudden acceleration of the guide bar combined with the inertia of the hand guard (L/1) will automatically actuate the chain brake. To engage the chain brake manually, simply push the hand guard (L/1) forward (towards the tip of the saw) with your left hand (arrow 2). Releasing the chain brake Pull the hand guard (L/1) towards you (arrow 3) until you feel it catch. The brake is now released. Fuel / Refuelling B 1.0 Us-gal. (3.7 l) 3.2 floz.(94 cm3) 2.5 floz.(75 cm3) 1.3 floz.(38 cm3) 2.5 Us-gal. (9.4 l) 8.0 floz.(236 cm3) 6.4 floz.(189 cm3) 3.2 floz.(94 cm3) 5.0 Us-gal. (18.9 l) 16.0 floz.(473 cm3) 12.8 floz.(378 cm3) 6.4 floz.(189 cm3) 100:1Gasoline 40:1 50:1 + other oil MAKITA oil MAKITA oil OIL 50:1 HP 100 Fuel mixture The engine of the chain saw is a high-efficiency two-stroke engine. It runs on a mixture of gasoline and two-stroke engine oil. The engine is designed for unleaded regular gasoline with a min. octane value of 91 ROZ. In case no such fuel is available, you can use fuel with a higher octane value. This will not affect the engine. In order to obtain an optimum engine output and to protect your health and the environment use unleaded fuel only. Gasoline which contens alcohol should not used in MAKITA products. For lubricating the engine use a two-stroke engine oil (quality grade: TC-3), which is added to the fuel. The engine has been designed for use of MAKITA HP 100 high-performance two-stroke engine oil and a mixture ratio of only 100:1 to protect the environment. In addition, a long service life and reliable operation with a minimum emission of exhaust gases are ensured. M...
Ce manuel est également adapté pour les modèles :Benzo et scies - DCS 6000I (2.44 mb)