Évaluations - 3, GPA: 3.7
(
)
)
|
Facilité d'utilisation
ADVERTENCIA PELIGRO 2 GUIDE BAR CHAIN REPLACEMENT BAR AND CHAIN PART NO. TYPE. LINKS NOTE: There may be other placement components for achieving kickback protection. For details, please refer to the chain and bar combination sheet shown in in the operator's manual 12" 120GPEA041 OREGON 91VG 45 14" 140GPEA041 OREGON 91VG 52 16" 160GPEA041 OREGON 91VG 57 STOP 8 3 7 CAUTION: This saw shall be used only by certified tree service professionals. For safe operation follow all safety precautions and instructions in the operator’s manual. (Replacement operator’s manuals are available from your Shindaiwa dealer. Hold chain saw firmly with both hands. 4 6 TO AVOID KICKBACK Contact of the guide bar tip with any object 1. should be avoided. Tip contact may cause the guide bar to move 2. suddenly upward and backward which may cause serious injury. Always use two hands when operating the 3. chain saw. 5 kick guard® to bar instructions For saws with Kick Guard® and symmetrical or asymmetrical low- kick type guide bars. Install bolt (A) in rear hole (B) of Kick Guard® and through front 1. hole (C) in guide bar. 2. IMPORTANT: Dimple in Kick Guard® (D) must engage recess in guide bar (E). Tighten nut (F) and bolt (A) until snug. Make certain Kick Guard® 3. is flush against guide bar. guide bar and saw chain-install/ remove Move chain brake lever (G) fully rearward to unlock chain brake.1. Remove two guide bar nuts (H). Turn tension adjustment screw (J) 2. counterclockwise 2 to 3 turns if bar and chain are installed. Push clutch cover (K) forward, pull rear of cover out slightly, then 3. remove. Remove guide bar and saw chain if necessary.4. Mount guide bar (L) on studs, and slide toward sprocket to make 5. saw chain installation easier. Install saw chain (M) over clutch and place around sprocket and guide bar as shown, with cutters on top of guide bar facing forward. Align holes of clutch cover (K) with guide bar studs, and tensioner pin 6. (N) with lower guide bar adjuster hole. Install cover, then press and hold rear of cover to fully seat. Tighten guide bar nuts finger tight. WARNING DANGER Saw Chain is sharp! Always wear gloves when handling assembly, otherwise serious personal injury may result. G H K J IMPORTANT Always loosen guide bar nuts before turning chain tension adjuster, otherwise clutch cover and tensioner will be damaged L N M NOTE: See “MAINTENANCE AND CARE” instructions for guide bar, sprocket, and saw chain maintenance. Turn saw over and check brake band (O) for correct position 7. around clutch drum (P). If brake band is not in place around drum, remove clutch cover, make sure brake is released, and reinstall. Adjust saw chain tension, as instructed in “Adjustment, Chain 8. Tension” Kick Guard to bar instructions, continued DANGER Never operate saw if chain brake does not function properly, otherwise saw damage and serious personal injury could result. See “Testing the Brake” instructions. O P ADJUSTMENT, CHAIN TENSION Remove air filter cover and spark plug lead.1. Loosen two guide bar nuts (H).2. Hold the bar nose up, and turn the adjuster screw (J) clockwise 3. until the chain touches the bottom of the bar. Tighten both guide bar nuts with bar nose held up.4. Pull the saw chain around the guide bar by hand. Reduce chain 5. tension, if you feel tight spots. Keep chain properly tensioned at all times.6. Replace spark plug lead and air filter cover.7. IMPORTANT Always loosen guide bar nuts before turning chain tension adjuster, otherwise clutch cover and tensioner will be damaged. J H IMPORTANT! Tighten guide bar nuts to 90 – 110 kgf/cm (80 – 95 in. lbs.) DO NOT over-tighten nuts. Damage to saw may result. NOTE All chains require frequent adjustments. Fuel and Lubricant NOTICE: Use of unmixed, improperly mixed, or fuel older than 90 days, (stale fuel), may cause hard starting, poor performance, or severe engine damage and void the product warranty. Read and follow instructions in the Storage section of this manual. fuel statement WARNING Alternative fuels, such as E-20 (20% ethanol), E-85 (85% ethanol) or any fuels not meeting Shindaiwa requirements are NOT approved for use in Shindaiwa 2-stroke gasoline engines. Use of alternative fuels may cause performance problems, loss of power, overheating, fuel vapor lock, and unintended machine operation, including, but not limited to, improper clutch engagement. Alternative fuels may also cause premature deterioration of fuel lines, gaskets, carburetors and other engine components. Gasoline: Use 89 Octane [R+M/2] (mid grade or higher) gasoline known to be good quality. Gasoline may contain up to 10% Ethanol (grain alcohol) or 15% MTBE (methyl tertiary-butyl ether). Gasoline containing methanol (wood alcohol) is NOT approved. Two Stroke Oil: Oil is a registered JASO FC classified oil and also meets or exceeds ISO-L-EGD performance requirements. Shindaiwa One is recommended for use in all Shindaiwa low emissions engines.Shindaiwa One also includes a fuel stabilizer. ...
Ce manuel est également adapté pour les modèles :Benzo et scies - 82085 (2.49 mb)