Évaluations - 3, GPA: 3.7 ( )

Fabricant : Homelite Taille : 24.71 mb Nom Fichier : Langue d'enseignement:

SYMBOL NAME DESIGNATION/EXPLANATION Safety Alert Indicates a potential personal injury hazard. Read Operator’s Manual To reduce the risk of injury, user must read and understand operator’s manual before using this product. Wear Eye and Head Protection Always wear eye protection with side shields marked to comply with ANSI Z87.1, along with head protection. SAFE-T-TIP Nose Guard The SAFE-T-TIP nose guard on the guide bar helps prevent rotational kickback. No Smoking No smoking, sparks, or open flame. Operate With Two Hands Hold and operate the saw properly with both hands. One Handed Do not operate the saw using only one hand. Carbon Monoxide Engines produce carbon monoxide which is an odorless, deadly poison. Do not operate in an enclosed area. Kickback DANGER! Beware of kickback. Bar Nose Contact Avoid bar nose contact. Wear Gloves Wear non-slip, heavy-duty protective gloves when handling the chain saw. Wear Safety Footwear Wear non-slip safety footwear when using this equipment. Gasoline and Lubricant Use unleaded gasoline intended for motor vehicle use with an octane rating of 87 [(R + M)/2] or higher. This product is powered by a 2-cycle engine and requires pre-mixing gasoline and 2-cycle lubricant. Keep Bystanders Away Keep all bystanders and animals at least 50 ft. away. GLOSSARY OF TERMS Bucking The process of cross cutting a felled tree or log into lengths. Chain Brake A device used to stop the saw chain. Chain Saw Powerhead A chain saw without the saw chain and guide bar. Clutch A mechanism for connecting and disconnecting a driven member to and from a rotating source of power. Drive Sprocket or Sprocket The toothed part that drives the saw chain. Felling The process of cutting down a tree. Felling Back Cut The final cut in a tree felling operation made on the opposite side of the tree from the notching undercut. Front Hand Guard A structural barrier between the front handle of a chain saw and the guide bar, typically located close to the hand position on the front handle, and sometimes employed as an activating lever for a chain brake. Front Handle The support handle located at or toward the front of the chain saw. This handle is for the left hand. Guide Bar A solid railed structure that supports and guides the saw chain. Kickback The backward or upward motion, or both, of the guide bar occurring when the saw chain near the nose of the top area of the guide bar contacts any object such as a log or branch, or when the wood closes in and pinches the saw chain in the cut. Kickback (Pinch) The rapid pushback of the saw which can occur when the wood closes in and pinches the moving saw chain in the cut along the top of the guide bar. Kickback (Rotational) The rapid upward and backward motion of the saw which can occur when the moving saw chain near the upper portion of the tip of the guide bar contacts an object, such as a log or branch. Low-Kickback Chain A chain that complies with the kickback performance requirements of ANSI B175.1 when tested on a representative sample of chain saws. Normal Cutting Position Those positions assumed in performing the bucking and felling cuts. Notching Undercut A notch cut in a tree that directs the tree’s fall. Rear Handle The support handle located at or toward the rear of the saw. It normally contains the throttle. This handle is for the right hand. Reduced Kickback Guide Bar A guide bar which has been demonstrated to reduce kickback significantly. Replacement Saw Chain A chain that complies with the kickback performance requirements of ANSI B175.1 when tested with specific chain saws. It may not meet the ANSI performance requirements when used with other saws. SAFE-T-TIP® Nose Guard An attachment that may be provided on the end of the guide bar to prevent the chain at the end of the guide bar from contacting the wood. Saw Chain A loop of chain having cutting teeth that cut the wood, and that is driven by the motor and is supported by the guide bar. Springpole A small tree (sapling) or limb that is bent or trapped under tension. It may “spring back” rapidly when cut, causing a dangerous situation. FEATURES PRODUCT SPECIFICATIONS Bar length: UT10544, UT10546..................................14 in. UT10564, UT10566..................................16 in. UT10584, UT10586...................................18 in. Chain pitch............................................ 0.375 in. Chain gauge.......................................... 0.050 in. Chain type........................Low Profile Skip Tooth Drive sprocket..........................................6-tooth Engine displacement....................................42cc Engine power.......................................2 HP min. Idle engine speed.........2,600-3,400 r/min. (RPM) Fuel tank capacity...................................11.5 oz. Chain lubricant tank capacity....................6.5 oz. Weight - No bar, chain, fuel or lubricant...9.8 lbs. STARTER GRIP TRIGGER RELEASE MUFFLER THROTTLE TRIGGER FRONT HAND GUARD/ C...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :