Évaluations - 2, GPA: 3.5
(
)
)
|
Facilité d'utilisation
ASSEMBLY Your saw is fully assembled; no assembly is necessary. KNOWYOURSAW READTHISMANUALRULESBEFOREOPERAT OPERATOR'SANDSAFETY ING YOUR CHAIN SAW, Compare the illustrations with your unit to familiarize yourself withthe location of the various controls and adjustments. Save this manual for future reference. rToo, " Hand Guard.---_ A_._. Handle k S .or.ope "NL .1 t I.,I I_ /_._ switch Chain Muffler _ . Pdmer Bar Oil Fill Cap Housing Cylinder Cover Fast Idle AdjustingScrew Fuel Mix FillCap Chain Direction of Travel Throttle Choke } Bar Clamp Nuts Guide Bar Tdgger Knob Bar Clamp Chain Catcher ON/STOP SWITCH The ON/STOP Switch is used to stop the engine. THROTTLE TRIGGER The throttle trigger controls engine speed. THROTTLE LOCKOUT The throttle lockout must be pressed before you can squeeze the throttle trigger. This feature prevents you from accidentally squeezing the trigger. FAST IDLE LOCK The fast idle lock holds the throttle trigger in the starting position, Activate the fast idle lock by pressing the throttle lockout and squeezing the throttle trigger. With the throttle trigger squeezed, press the fast idle lock. Release the throttle lockout and trigger while holding the fast idle lock button. CHOKE KNOB The Choke Knob activates the choke to provide additional fuel to the engine during cold starting. PRIMER BULB The Primer Bulbcirculates fuel to the carburetorto providequicker starting, CHAIN TENSION It is normal for a new chain to stretch during first 30 minutes of operation. You should check your chain tension frequently. See Chain Tension under the Service and Adjustments section. 6 BEFORE STARTING ENGINE lines and carburetor are empty. Use fresh fuel next season. See STORAGE instruc- WARNING: Be sureto read the fuel tions for additionalinformation. handlinginformationinthesafety rules Never use engine or carburetor cleaner sectionofthismanual beforeyoubegin. products in the fuel tank or permanent If youdonotunderstandthe fuel han damage may occur. dlinginformationdo notattemptto fuel See the STORAGE section for additional your unit.Seekhelpfrom someonethat information. does understandthe informationor call STOPPING YOUR ENGINE the customerassistancehelp lineat 1-800-235-5878. • Move On/Stop switch to STOP. • If engine does not stop, pull choke GUIDE BAR AND CHAIN OIL knob out fully. The chain oiler provides continuous lu- STARTING YOUR ENGINE brication to the chain and guide bar. Be sure to fill the bar oil tank when you fill COLD ENGINE OR WARM ENGINE AFTER RUNNING OUT OF FUEL For maximum guide bar and chain life, the fuel tank (Capacity = 6.8 fl. oz.). • Fuel engine with 40:1 fuel mix. • Fill bar oil tank with bar oil. we recommend you use Craftsman chain saw bar oil. If Craftsman bar oil is • Prime engine by slowly pressing primer bulb six times. not available, you may use a good grade SAE 30 oil until you are able to • Move OntStop switch to ON. obtain Craftsman brand. The oil output PrimerBulb is automatically metered during operation, Your saw will use approximately one tank of bar el! for every tank of fuel mix. Always fill the bar oil tank when s tch you fill the fuel tank, .... FUEUNG ENGINE CHOKE POSITIONS This engine is certified to operate on unleaded gasoline. Before operation, k_! gasoline must be mixed with a good I Off Full quality 2-cycle air-cooled engine oil. We recommend Craftsman brand oil. Mix • Actuate choke by pulling choke knob gasoline and oil at a ratio of 40:i (A fulfy out. • Set saw on the ground. Grip front ounces of oil with 1 gatlon of unleaded handle with your left hand and place gasoline). DO NOT USE automotive oil right foot through rear handle. or boat oil. These oils will cause engine 40:1 ratio is obtained by mixing 3.2 Starter RopeHandle damage. When mixing fuel follow the instructions printed on the container. Once oil is added to the gasoline, shake container momentarily to assure that the fuel is thoroughly mixed. °.n 22t Always read and follow the safety rules relating to fuel before fueling your unit. IMPORTANT Experience indicatesthat ak:ohol blended RightFoot ThroughRear Handle fuels (called gasohol or using ethanol or methanol) can attract moisture which • Set fast idle by depressing the throttle leads to separationand formation of lock with your right hand. Then, acids during storage. Acidic gas can squeeze and hold throttle trigger. With damage the fuel system of an engine dYourthumb, press the fast idle lock while in storage. own and hold. Next, release the To avoid engine problems,the fuel sys-throttle trigger. tem should be emptied before storage for • DO NOTsqueeze throttle trigger dur30 days or longer. Drain the gas tank, ing starting; otherwise, it will be necstart the engine and let it run until the fuel essary to reset the fast idle lock. 7 NOTE: When pulling the starter rope, OPERATING TIPS do not use the full extent of the rope. • Check chain tension before first use Do not let starter rope snap back. Hold and after 1 minute of operation. See ...
Ce manuel est également adapté pour les modèles :Benzo et scies - 358.352680 - 18 IN. BAR (2.69 mb)
Benzo et scies - 358.352680 - 18 IN. BAR (2.69 mb)
Benzo et scies - 358.352680 - 18 IN. BAR (2.69 mb)