Log:
Évaluations - 4, GPA: 4 ( )

Instructions Poulan, Modèle 315.21213

Fabricant : Poulan
Taille : 1.36 mb
Nom Fichier : L0205057.pdf
Langue d'enseignement: en
Aller à la télécharger



Facilité d'utilisation


MITER FENCE BLADE COMBINATION MITER SQUARE TABLE VIEWOF BLADENOTSQUAREWITHMITER TABLE,ADJUSTMENTSAREREQUIRED Fig. 22 •MITER FENCE BLADE COMBINA_ON MITER SQUARE TABLE VIEWOF BLADENOTSQUAREWITHMITER TABLE,ADJUSTMENTSAREREQUIRED Fig. 23 Using a 10 mm wrench or adjustable wrench, loosen the lock nut securing positive stop adjustment screw. Also loosen bevel lock knob. Adjust positive stop adjustment screw to bring saw blade into alignment with the square. See Figures 24 and 25. 17 POSITIVESTOP ADJUSTMENT SCREWFOR Fig. 24 Retighten bevel lock knob. Next, retighten lock nut securing the positive stop adjustment screw. Recheck blade-to-table alignment. Note: The above procedure can be used to check blade squareness of the saw blade to the miter table at both O°and 45° angles, Your saw has three scale indicators, two on either side of the bevel scale and one on the miter scale. After squaring adjustments have been made, it may be necessary to loosen the indicators screws and reset them to zero. cu'n'ING A SLOT IN THE ZERO CLEARANCE THROAT PLATE In order to use your compound miter saw, you must cut a slot through the zero clearance throat plate to allow for blade clearance. To cut the slot, set your saw at0° miter, turn saw on and allow the blade to reach full speed, then carefully make a straight cut as far as it will go through the throat plate. Turn your saw off and allow the blade to come to a complete stop before raising the saw arm. Next, adjust the bevel angle to 45 °,turn your saw on and allow the blade to reach full speed, then carefully make another cut through the zero clearance throat plate. The slot in the throat plate will then be wide enough to allow the blade to pass through it at any angle from O° to 45°. PIVOT ADJUSTMENTS Note: These adjustments were made at the factory and normally do not require readjustment. TRAVEL PIVOT ADJUSTMENT The saw arm should rise completely to the up position by itself. If the saw arm does not raise by itself or if there is play in the pivot joints, have saw repaired by a qualified service technician at your nearest Sears store or repair center to avoid risk of personal injury. BEVEL PIVOT ADJUSTMENT • Your compound miter saw should bevel easily by loosening the bevel lock knob and tilting the saw arm to the left. If movement is tight or if there is play in the pivot, have saw repaired by a qualified service technician at your nearest Sears store or repair center to avoid risk of personal injury. DEPTH STOP The depth stop limits the blade's downward travel. It allows the blade to go below the miter table enough to maintain full cutting capacities. The depth stop positions the blade 1/4 in. from the miter table support. Note: The miter table support is located inside miter table. The depth stop is factory set to provide maximum cutting capacity for the 10 in. saw blade provided with your saw. Therefore, the saw blade provided should never need adjustments. However, when the diameter of the blade has been reduced due to sharpening, it may be necessary to adjust the depth stop to provide maximum cutting capacity. Also, when a new blade is installed, it is necessary to check the clearance of the blade to the miter table support before starting the saw. Make adjustments if needed. DEPTH STOP ADJUSTMENTS See Figure 25. • Unplug your saw, _I, WARNING: Failure to unplug your saw could result in accidental starting causing possible sedous personal injury. To adjust the depth stop use a 17 mm wrench or adjustable wrench and loosen the hex nut at the rear of the miter saw arm. Use the 5 mm hex key wrench provided to adjust the depth stop adjustment screw. The saw blade is lowered by turning the screw counter-clockwise and raised by turning the screw clockwise. 18 DEPTHSTOP ADJUSTMENT SCREW ) BEVEL TABLE POSITIVE STOPADJUSTMENT LOCKNUT(S) SCREWFOR0° ANGLES Fig. 25 • Lower the blade into the zero clearance throat plate of the miter table. Check blade clearance and maximum cutting distance (distance from fence where blade enters) to front of miter table slot. • Readjust if necessary. _k, WARNING: Do not start your compound miter saw without checking for interference between the blade and the miter table support. Damage could result to the blade if it strikes the miter table support during operation of the saw. Tighten the hex nut with a 17 mm wrench or adjustable wrench. To prevent the depth stop adjustment screw from turning while tightening the hex nut, carefully hold it with the hex key wrench while tightening the hex nut. APPLICATIONS (Use only for the purposes listed below) • Cross cutting wood and plastic. • Cross cutting miters, joints, etc. for picture frames, moldings, door casings, and fine joinery. Note: The blade provided is fine for most wood cutting operations, but for fine joinery cuts or cutting plastic, use one of the accessory blades available from your nearest Sears store. _h, WARNING: Before starting any cutting operation, clamp or bolt your compound miter saw to ...

Ce manuel est également adapté pour les modèles :
Benzo et scies - 315.21213 (1.36 mb)
Benzo et scies - 315.21213 (1.36 mb)
Benzo et scies - 315.21213 (1.36 mb)

Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories