Évaluations - 2, GPA: 4
(
)
)
|
Facilité d'utilisation
You can adjust the chain tension by loosening the chain brake nuts and turning the adjusting screw 1/4 of a turn while lifting up on the bar. S If chain is too tight, turn adjusting screw 1/4 turn counterclockwise. S If chain is too loose, turn adjusting screw 1/4 turn clockwise. AdjustingScrew Guide Bar Adjusting Screw - --1/4 Turn Chain Brake Nuts S Lift up the tip of the bar and securely tighten the chain brake nuts with the bar tool. S Recheck chain tension. ChainBrakeNuts WARNING: If the saw is operated with a loose chain, the chain could jump off the guide bar and result in serious injury. 7 8 OPERATION KNOW YOUR SAW READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR CHAIN SAW. Compare the illustrations with your unit to familiarize yourself with the location of the various controls and adjustments. Save this manual for future reference. Chain Adjustment Tool (Bar Tool) Primer Bulb Fuel Mix Fill Cap Starter Housing Bar Oil Fill Cap Chain Front Hand Guard Front Handle Starter Rope ON/STOP Switch Muffler Bar Sprocket Hole Chain Brake Nuts Guide Bar Cylinder Cover Throttle Lockout Rear Handle Throttle Trigger Choke/ Fast Idle Lever Chain Brake Chain Direction of Travel Chain Catcher Adjusting Screw ON/STOP SWITCH The ON/STOP SWITCH is used to stop the engine. THROTTLE TRIGGER The THROTTLE TRIGGER controls engine speed. THROTTLE LOCKOUT The THROTTLE LOCKOUT must be pressed before you can squeeze the throttle trigger. This feature prevents you from accidentally squeezing the trigger. CHOKE/FAST IDLE LEVER The choke and fast idle are set by pulling the CHOKE/FAST IDLE LEVER out fully for cold or refueled starting. The choke provides additional fuel to the engine during cold starting. PRIMER BULB The PRIMER BULB circulates fuel to the carburetor to provide quicker starting. CHAIN BRAKE The CHAIN BRAKE is a device designed to stop the chain if kickback occurs. The chain brake activates automatically in the event of kickback. The chain brake activates manually if the front hand guard is pushed forward. The chain brake is disengaged by pulling the front hand guard back toward the front handle as far as possible. CHAIN TENSION It is normal for a newchain to stretch during first 30 minutes of operation. You should check your chain tension frequently. See CHAIN TENSION under the ASSEMBLY section. WARNING: Muffler is very hot during and after use. Do not touch the muffler or allow combustible material such as dry grass or fuel to do so. FUELING & LUBRICATION WARNING: Remove fuel cap slowly when refueling. FUELING ENGINE This engine is certified to operate on unleaded gasoline. Before operation, gasoline must be mixed with a good quality synthetic 2-cycle air-cooled engine oil designed to be mixed at a ratio of 40:1. Poulan/Weed Eater brand synthetic oil is recommended. Mix gasoline and oil at a ratio of 40:1. A 40:1 ratio is obtained by mixing 3.2 ounces (95 ml) of oil with 1 gallon (4 liters) of unleaded gasoline. Included with this saw is a 3.2 ounce container of oil. Pour the entire contents of this container into 1 gallon of gasoline to achieve the proper fuel mixture. DO NOT USE automotive oil or boat oil. These oils will cause engine damage. When mixing fuel, follow instructions printed on container. Once oil is added to gasoline, shake container momentarily to assure that the fuel is thoroughly mixed. Always read and follow the safety rules relating to fuel before fueling your unit. BAR AND CHAIN LUBRICATION The bar and chain require continuous lubrication. Lubrication is provided by the automatic oiler system when the oil tank is kept filled. Lack of oil will quickly ruin the bar and chain. Too little oil will cause overheating shown by smoke coming from the chain and/ or discoloration of the bar. In freezing weather oil will thicken, making it necessary to thin bar and chain oil with a small amount (5 to 10%) of #1 Diesel Fuel or kerosene. Bar and chain oil must be free flowing for the oil system to pump enough oil for adequate lubrication. Genuine PoulanR bar and chain oil is recommended to protect your unit against excessive wear from heat and friction. PoulanR oil resists high temperature thinning. If PoulanR bar and chain oil is not available, use a good grade SAE 30 oil. S Never use waste oil for bar and chain lubri cation. S Always stop the engine before removing the oil cap. IMPORTANT Experience indicates that alcohol- --blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage for 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See STORAGE section for additional information. 9 Lefthandonfronthandle Rightfootthroughrearhandle STARTING WARNING: The chain must ...