Log:
Téléchargements : 2   Taille : 1 mb   Fabricant : Dolmar  
Catégorie : Benzo et scies
@name@name

Lubrication of the sprocket tip is recommended after 10 hours of use or once a week, which ever occurs first. Always thoroughly clean guide bar sprocket tip before lubrication. The Lube Gun (optional) is recommended for applying grease to the guide bar sprocket tip. The Lube Gun is equipped with a needle nose tip which is necessary for the efficient application of grease to the sprocket tip. Fig. 37 To lubricate the sprocket tip: 1. Move the STOP switch down. NOTE: It is not necessary to remove

Téléchargements : 0   Taille : 28 mb   Fabricant : Dolmar  
Catégorie : Benzo et scies
@name@name@name

. . . . . . . . . .13 Troubleshooting Chart . . . . . . . . . . . . . . . . . . . . . .19 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 Warranty Information . . . . . . . . . . . . . . . . . . . . . . .20 Parts List . . . . . . . . . . . . . . . . . . . .Inside Back Cover Copy the model and parent part number here: Copy the serial number here: Make sure you carefully read and understand this manual before starting or operating this equipment. THIS PRODUCT IS COVERED

Téléchargements : 2   Taille : 265 kb   Fabricant : Dolmar  
Catégorie : Benzo et scies
@name

C-6CG-9.5 C RING 1 60 MC-6PC05-14.7 PIN 26 MC-6014-210502 WASHER 1 61 MC-6PC4.4-35 PIN 1 27 MC-6228-210104 GEAR BEARING ASS'Y 1 62 MC-6SQAB-04-06 SCREW 28 MC-6077-211501 COVER 1 63 MC-6WFB-03-12 WASHER 1 29 MC-6057-210102 WASHER 1 64 MC-6SDABB03-15 SCREW 30 MC-6CC-10 C RING 1 65 MC-6158-211502 PLATE 1 32 MC-6SDABB03-18 SCREW 1 66 MC-6SLABB03-06 SCREW 33 MC-6228-210105 OIL PUMP ASS'Y 1 67 MC-6010-211301 WIRE 1 34 MC-6188-211501 PULL BAR 1 68 MC-6SDABB04-14 SCREW 3 35

Téléchargements : 4   Taille : 2 mb   Fabricant : Dolmar  
Catégorie : Benzo et scies
@name@name@name

Ensure that the WARNING: power cord is disconnected before performing any maintenance on your saw. Sprocket Tip Lubrication The sprocket tip on CAUTION: your new saw has been pre-lubricated at the factory. Failure to lubricate the guide bar sprocket tip as explained below will result in poor performance and seizure, voiding the manufacturer’s warranty. Lubrication of the sprocket tip is recommended after each saw use. Always thoroughly clean guide bar sprocket tip before lubrication. The Lube Gu

Téléchargements : 2   Taille : 2 mb   Fabricant : Dolmar  
Catégorie : Benzo et scies
@name

Téléchargements : 8   Taille : 2 mb   Fabricant : Dolmar  
Catégorie : Benzo et scies
@name

Téléchargements : 20   Taille : 2 mb   Fabricant : Dolmar  
Catégorie : Benzo et scies
@name

Téléchargements : 17   Taille : 2 mb   Fabricant : Dolmar  
Catégorie : Benzo et scies
@name

Téléchargements : 19   Taille : 2 mb   Fabricant : Dolmar  
Catégorie : Benzo et scies
@name

Téléchargements : 180   Taille : 6 mb   Fabricant : Dolmar  
Catégorie : Benzo et scies
@name@name

Be careful not to spill fuel or chain oil! Tightly screw on the cap. After refuelling, clean screw cap, tank and check for lekages. Lubricating the chain During operation there must always be sufficient chain oil in the chain-oil tank to provide good chain lubrication. One filling is sufficient for about one half-hour of continuous operation. While working make sure there is enough chain oil in the tank. If necessary, add oil. The engine must be switched off! NEVER USE WASTE OIL Waste oil is ver





catégories