Évaluations - 4, GPA: 4.3
(
)
)
|
Facilité d'utilisation
High will reject more, low will reject less. LED Light – Turns the LED Lights OFF Reset the V1 – Deletes all pairing information resets the Voice Interface and reboots the headset back into pairing mode BlueAnt Phone Commands – Triggers the Voice Dial function of your cell phone (If your phone supports voice dialing) Redial – Calls the number you last dialed Call Back – Calls the last received number Call Voice Mail – Calls your Voicemail Call Home – Calls your Home Call Offi ce – Calls your Office Call Favorite – Dials your favorite number Call GOOG-411 – Connects you to the GOOG-411 service, see for details Call Speed Dial 6 – Dials the number you have set to Speed Dial 6 Call Speed Dial 7– Dials the number you have set to Speed Dial 7 Call Speed Dial 8 – Dials the number you have set to Speed Dial 8 Call Speed Dial 9 – Dials the number you have set to Speed Dial 9 Switch Headset Off - Turns the headset OFF Cancel – Cancels the active operation ENGLISH BlueAnt VOICE CONTROL – Voice Answer On an incoming call the headset will announce the Caller ID. It will then ask you if you want to Answer or Ignore the Call Say “ANSWER” to accept the call OR “IGNORE” to reject the call Note : If the voice recognition in the V1 cannot understand you because of high noise or a loud ringtone coming from the phone, it will ask you to press the BAB once to answer or twice to Ignore the call. BUTTON OPERATION To Turn Voice Control ON or OFF Press and Hold Vol + and Vol - for 6 Seconds Pairing Pairing need only be done once for each device you use. The V1 can store pairing information for up to 8 different Bluetooth devices. To pair another phone, make sure the first paired phone has Bluetooth switched off or is out of range. If you want to connect to a previously paired phone, use that phones Bluetooth Menu to connect. Note: You can say ‘Pair Me’ to enter pair mode at any time, or follow the steps below BlueAnt Pairing Procedure (This is an example only and may differ from your phone, but the process will be the same.) 1. First turn the phone OFF and then back ON again to refresh its memory. 2. Bring the mobile phone to about 30cm from the V1 Device. 3. Find the Bluetooth menu in your mobile phone. Turn Bluetooth ON. (Check your mobile phone user guide if necessary) 4. With the V1 OFF, Press and Hold the BAB for about 6 seconds. The LED will appear a solid Blue, and then will start flashing. The V1 is now in Pairing mode and ready to be found in searches by other Bluetooth devices. Pairing mode will be active for 2 minutes. 5. Perform a Bluetooth device discovery on your mobile phone to add a new device. (It takes a few seconds to search for and find other Bluetooth devices around you). 6. When Bluetooth devices are found, the phone will display “BlueAnt V1”. Scroll to it and press OK to confirm that you want to Pair with it. 7. Enter Passkey “0000” when your phone prompts you. The phone and V1 will now Pair. 8. An additional security setting in your phone may be needed to allow the headset and phone to connect automatically without confirmation each time you connect your V1. Generally in the options for the BlueAnt V1, it will be referred to as “set as authorized”, “add to trusted devices”, ‘’allow connection’’ or similar. 9. If required for first time connection, select the BlueAnt V1 to connect with your phone. OR, Click the BAB on the V1, to connect with the phone. ENGLISH BlueAnt Basic Headset Functions For easy reference, also see the Button/Function Matrix and the Quick Start Guide. 1. Power ON: Press and Hold the BAB for 3 seconds. The solid Blue LED will light up. If the battery is low a solid Red LED will be displayed. After powering ON, your headset will automatically connect to your last used phone if it is in operating range. If this phone is not range, the V1 will enter idle mode after 60 seconds. If no phone has yet been Paired, it will enter the welcome prompt. 2. Power OFF: Press and Hold the BAB for 3 seconds. The Red LED flashes three times. Power Off works on Standby/ Idle mode. 3. Enter Pairing Mode: With the V1 OFF, Press and Hold the BAB for about 6 seconds until the LED flashes Blue. The V1 will stay in pairing mode for 2 minutes then will go into idle mode. To re-enter pairing mode, repeat this step, or say “Pair Me” 4. Make a Call: Dial the number using your phones keypad as normal. Audio will automatically transfer to the headset. 5. To Answer a call: Click the BAB once when there is an incoming call. 6. To End a call: Double Click the BAB to end the call. 7. Reject: Double Click the BAB to reject an incoming call. 8. Redial the last call : Press and Hold Vol for about 3 seconds. To cancel Redial, click the BAB 9. Activate Phone Commands (Voice Dialling)*: While connected to a phone, press the BAB once. Voice commands must have been previously recorded into your phone (see your phones user guide for specific instructions. (Button Only Mode) 10. Reconnect: To reconnect ...