Évaluations - 3, GPA: 3.3
(
)
)
|
Facilité d'utilisation
Place blender base on clean, dry surface to keep foreign particles from being pulled up into motor during operation. 2. Align dispenser lever with spring facing base. Insert one side of dispenser lever tabs into notches on front of the base. Press dispenser lever to the side to allow the second tab to slide into a notch on base. 3. For dispenser assembly and cutting assembly instructions, see the “Cleaning” section. 4. For thermal jar models, insert blending jar into thermal jar. 5. Fit gasket over blades. The gasket must lie flat. Set jar on top of gasket and screw on cutting assembly. 6. Make sure the cutting assembly is firmly screwed onto the jar. 7. OPTION: When dispenser is not needed replace the dispenser with the spout cap. 4 Remove dispenser assembly (see “Cleaning” section). Insert spout cap on cutting assembly. Turn spout cap clockwise to lock. 8. Set jar into place on blender base, making sure it is securely seated. If not, gently rock the jar until seated. NOTE: The cutting assembly must slide between the base and dispensing lever. 9. Plug cord into outlet. 10. Put ingredients in jar; lock filler cap and lock lid on jar. Always hold handle when blending. 11. Process food or beverages. See the “Blending Techniques” section for speeds and processing tips. NOTE: When blending thin liquids, do not fill above the 40-ounce/ 5 cup/1200 ml mark on blender jar. 12. The dispensing blender will dispense beverages. To dispense, press drink cup against dispenser lever. Dispensing will automatically stop when the cup is removed. To dispense thick liquids (such as milkshakes, smoothies, frozen drinks, etc.), turn blender ON and then dispense. Turn OFF after dispensing. 13. ALWAYS turn blender off and wait until blades have stopped rotating before removing jar. 14. To remove jar after blending is complete, lift the jar straight up. If it is not easily removed, rock gently and lift. Do not twist. 15. NEVER replace jar onto unit while motor is running. 840131900 ENv01.qxd 2/22/05 10:40 AM Page 5 Speed Control Panels ICEBREAKER OFF SPEED8OFF ICEBREAKER TM OFF SPEED01ICEBREAKER Pulse First select and push a LO or HI power Both Pulse 1 and Pulse 2 may be used button then push desired speed button. on HI and LO speed settings. For the When using PULSE or Ice Breaker™ but-highest speed, push HI and Pulse 2. tons, blender will operate only as long as button is pushed. The remaining speed buttons will run the blender until OFF is pushed. Quick Cleaning Quick cleaning should only be used to rinse the blender between batches of processing the same food. When the processing of a single type of food is finished, the blender should be disassembled and thoroughly cleaned as instructed in “How to Clean.” To quick clean, pour 2 cups (500 ml) warm water in jar and add 1 drop liquid dishwashing detergent. Run the blender on ICY DRINK for 10 seconds. Flush soapy water through dispenser until cleaned. Discard soapy water. Rinse blender jar with clean water. Flush clean water through dispenser until cleaned. This function is not a substitute for regular cleaning as instructed in “How to Clean.” This function should never be used when blending any mixture containing eggs, milk, or any other dairy products, meats, or seafood. 5 840131900 ENv01.qxd 2/22/05 10:40 AM Page 6 Crushing Ice Fill blender jar half-full with cold water. Add about 2 cups (500 ml) of ice cubes. Lock filler cap into lid and lock lid on blender jar. Press the ICY DRINK button. Continue until ice is crushed to desired consistency. Pour contents into colander or sieve to drain off water. Hints for Best Use DO NOT CRUSH ICE WITHOUT LIQUID. Failure to follow these directions can result in damage to the blades, jar, blender, and possibly result in personal injury. NOTE: After extended blending, especially dry food, you may notice a black film inside the top of the blender base. This is a normal, FDA-approved, food- grade lubricant used to ensure the long-life of your cutting assembly. • Processing hot foods or liquids in the blender may cause hot liquid to spurt out when the cover is removed. Always remove the filler cap of the lid before blending hot foods or liquids. Keep hands and other exposed skin away from the cover opening to reduce risk of possible burns. • To add foods when blender is operating, remove filler cap from container lid and add ingredients through the opening. • Do not store food or liquids in the blender jar. • If blending action stops during blending or ingredients stick to sides of the jar, turn blender OFF. Remove cover and use a rubber spatula to push mixture toward blades. • Do not try to mash potatoes, mix stiff dough, whip egg whites, grind raw meat, or extract juices from fruits and vegetables. The blender is not made to perform these tasks. • If food being processed (solid food or ultra-thick beverages) will not dispense always pour from jar. 6 840131900 ENv01.qxd 2/22/05 10:40 AM Page 7 Blending Techniques NOTE: Foods and liquids too thi...