Évaluations - 1, GPA: 3
(
)
)
|
Facilité d'utilisation
Ensure that the power source to be used is the same as the voltage requirements of the product. Always switch the appliance to off, switch the power off at the power outlet and then unplug from the outlet when the appliance is not being used and before cleaning. Never immerse the power cord, plug or blender body in any form of liquid. Always place the appliance on a dry, level surface when in use. Ensure the blender lid is securely in place before operating. Do not remove blender jug from the motor base whilst blender is in operation. Do not place your hands or utensils in the blender jug while the blender is operating. Do not place hands or utensils in the jug unless the unit is disconnected from the power outlet. Do not use this blender for anything other than food or beverage preparation. Do not blend hard food items such as nutmeg, lump sugar and ice. Do not operate blender continuously on heavy loads for more than 1 minute. Do not process boiling or hot liquids or ingredients, let them cool before placing into the jug. Do not place any part of the blender in the dishwasher Make sure the motor and blade have completely stopped before disassembling. This appliance is not intended for use by young children or infirm persons without supervision. Close supervision is required at all times when operating the appliance near children. Young children should be supervised to ensure that they do not play with the appliance. Do not leave the appliance unattended when in use. Do not let the cord hang over the edge of a table or counter, touch hot surfaces or become knotted. Do not place this appliance on or near a hot gas burner, electric element, or in a heated oven. This appliance is suitable for domestic use only. Do not use this appliance for anything other than its intended use. Do not use outdoors. Regularly inspect the supply cord, plug and actual appliance for any damage. If found damaged in any way, immediately cease use of the appliance and return the entire appliance to the nearest authorised Kambrook Service Centre for examination, replacement or repair. The installation of a residual current device (safety switch) is recommended to provide additional safety protection when using electrical appliances. It is advisable that a safety switch with a rated residual operating current not exceeding 30mA be installed in the electrical circuit supplying the appliance. See your electrician for professional advice. 2 Features of your Kambrook Mega Blend 123456 1. Removable filler cap – for adding additional ingredients during blending, liquid ingredients can be added when the cap is placed upside down and drip through the small hole in the cap 2. Extra large 1.6 litre capacity jug – for blending small or large quantities 3. Powerful 500W motor – powerful blending action. 4. Stainless steel blade assembly CAUTION Blades must be handled carefully as they are sharp! 5. 2 speeds dial plus pulse setting for all your blending needs 6.Wrap around cord storage with securing clip 3 Using Your Kambrook Mega Blend Before first use remove any promotional labels and wash the blender jug and lid in warm, soapy water, then dry. Place the blender motor base on a level, flat surface. Place the empty jug onto the base Place food or liquid into the jug and firmly push the lid on top of the jug. Ensure the speed dial is in the Off (O) position. Plug into a 230/240-volt power outlet. Turn power outlet on. When switching the unit on hold the lid down to ensure it is safely in place. To begin blending move the speed dial from the Off (O) position to either the Low (1) or High (2) speed, depending upon mixing requirements.The speed can be changed at any time during the blending process. When blending is complete, turn blender off by moving the speed dial to the Off (O) position.Wait until blades have stopped rotating before removing the lid or the blender jug from the base. Use the PULSE setting for ingredients that require short bursts of power. Hold the speed dial on this setting until desired blending is achieved.When released, the speed dial will automatically return to the Off (O) position. If ingredients stick to the sides of the blender jug during the blending process, turn the speed to the Off (O) position, switch off and unplug from the power outlet, then push the food back onto the blades using a plastic spatula to scrape down the sides of the jug.Then recommence blending. NOTE: If any moisture or liquid appears on top of the motor base, wipe immediately with paper towelling NOTE:When blending liquids a small amount of liquid may come up from around the filter cap.This is normal. Ensure that the filter cap is correctly in place BEFORE blending. Once blending has commenced (ie/ dial is in a position 1 or 2) you may remove the filler cap and add additional ingredients. NOTE: Ensure that the maximum level is not exceeded. Correctly fitting the filler cap Align the protruding nubs on the filler cap with the indents on the lid and p...