Évaluations - 3, GPA: 4 ( )

Fabricant : Panasonic Taille : 536.27 kb Nom Fichier : CFVFS251W.PDF Langue d'enseignement:

When the error message is displayed, press the enter key. In the Setup Utility, select "Load Default Settings (PnP)". This will restore the Setup Utility's settings to their default values, then the Setup Utility must be run once again to make the appropriate operating environment settings. 5 Software Preparation (first time only) 1 Power on. 2 Select [Start]-[ProgramsJ-(MS-DOS Prompt], then type the following command: DELTREE C:\UTlL\DRIVERS\LS120FDD When the message is displayed, press the Y key. 3 Insert the supplied "Superdisk Setup Disk" and type the following commands: XCOPY A:\*.* C:\UTlL\DRIVERS\LS120FDD\ EXIT 1 Insert a Superdisk Drive Pack into the multimedia pocket. 2 Power on. 3 Select [Start]-[Run], type [C:\util\drivers\ls120fdd\setup.exe], then press L_2^__J. Follow the on-screen instructions. 6 Mounting a Superdisk Drive Pack r(«> • Do not use the Superdisk Drive Pack during the initial boot up of the computer (when creating the Firstaid FD). • Do not install a Superdisk Drive Pack with a FDD cable (CF-VCF351). Mount it into the multimedia pocket. • When a Superdisk Drive Pack is installed, do not use a floppy disk drive pack with a FDD cable (CF-VCF351)._^ 1 Power off your computer {cr "Operating Instructions" of the computer, page 10) Do not shut down using the suspend or hibernation mode. {©fitMSca)------ In the suspend or hibernation mode, do not remove/change the multimedia pocket device. Removing the device in the suspend or hibernation mode may damage the device._^ 2 Turn your computer over and open the multimedia pocket cover 3 0 Removing a multimedia pocket device © Slide the MP release lever toward the MP device. The MP device should slide out. r\ (2) Pull out the device. GAUililON > • Be careful not to touch the Superdisk Drive Pack connector. • Gently install / remove any multimedia pocket device. Do not use excessive force when installing._ 0 Inserting a Superdisk Drive Pack Confirm that the Superdisk Drive Pack connector is facing the same direction as shown in the illustration. Push the unit in until it snaps into place. Confirm that the MP release lever has returned to its original position. Power on your computer Connector 7 Formatting a Disk The disk can be accessed by a Superdisk Drive Pack, the same as a floppy disk drive. When formatting the disk, using a Superdisk Drive Pack, execute the following procedure. 1 Insert the disk into the Superdisk Drive Pack. 2 Select [My Computer], place the mouse cursor on the [3 I/2 Floppy (A:)| icon and click the right touch pad button, then select (Format utility For SuperDisk*]. Set each item (if necessary), then click [Start]. The formatting will begin. * This menu is displayed only when ihe disk is iuseited in the drive. r(©£t№Mi3)- • When starting MS-DOS by selecting [Start] - [Programs] - [MS-DOS Prompt] with Windows 95, FORMAT A: command may not be executed. • DISKCOPY command can not be executed with [Start] - [Programs} - [MS-DOS Prompt], Select [My Computer], place the mouse cursor on the [3 1/2 Floppy (A:)J icon and click the right touch pad button, then select [Disk Copy], • DISKCOPY command does not support the Superdisk. • Uncheck "Auto Insert Notification" and "DMA" in [Start] - [Settings] - [Control Panel| - [SystemJ - [Device Manager] - [Disk Drive] - [MATSUSHITA LS-120 SLIM] - [Settings]. • It may take about 30 minutes to format the Superdisk. • When MS-Backup is executed, the message "No Controller board detected" may be displayed. In this case, replace the Superdisk Pack to the floppy disk drive, execute MS-Backup. When an error message is displayed, click [OK], then continue running the MS-backup program. After MS-Backup, insert the Superdisk Pack again. • When accessing an unformatted disk, the message if you want to format it or not is displayed. If you press [Yes], the disk cannot be formatted correctly. Format it with [Format utility For SuperDisk], • When accessing [Removable Disk (A:)] by the right button of the touch pad without the floppy disk drive or the Superdisk Drive Pack, it may take several minutes to resume. Using the Self-diagnosis Program Follow the procedure below to check whether each part of your computer is operating properly with the Superdisk Drive Pack. 1 Insert the Firstaid FD you created into the Superdisk Drive Pack, then turn your computer on. 2 At the boot-up menu, select [1. Boot]. 3 Type the following: DIAG25 /V The following screen is displayed: BIOS =Vx.xxLxx DIAG = Vx.xLxx y When "DIAG = V2.0" is displayed, go to 4. Otherwise, type the following: DIAG25 Follow the on-screen instructions. 4 Remove the Firstaid FD and insert the "CF-25 System Update” disk, then type the following: DIAG25E Follow' the on-screen instructions. i 9 Troubleshooting The computer does not recognize the Superdisk Drive Pack. • Have you installed the driver...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :