45° V H 45° 30° 15° V H 45° V H 45° V H 45° 15° 15° 45° V H 45° 15° 30° V H 280-7326-00 6 DISC CD CHANGER WITH CD TEXT Owner’s manual Thank you for purchasing the CDC655Tz/RDC655Tz system. The CDC655Tz/RDC655Tz is designed incorporating the latest digital technologies, while featuring a newly developed CD mechanism to achieve excellent performance and good reliability. Please read this owner’s manual entirely before proceeding with installation. 1 FEATURES 2 PRECAUTIONS 1. This unit does not operate independently. The unit must be used with a source unit that has a cable connection for CeNET wire bound (sold separately). 2. CD singles cannot be used. 3. The pickup, the heart of a player, is built in deep behind the door. Do not leave this door open for extended periods to prevent dust adhering to the pickup. When the inside of the car is very cold and the player is used soon after switching on the heater, dew may form on the disc or optical parts of the player and proper playback may not be possible. If dew forms on the disc, wipe it with a soft cloth. If dew forms on the optical parts of the player do not use the player for about one hour and the condensation will disappear naturally to allow normal operation. 4. While the system is in play, do not plug or unplug the cables as this will cause damage. 5. This unit is compatible with CD TEXT. When it is connected to a center unit suitable for CD TEXT display, CD TEXT can be displayed. (When it is connected to a center unit without CD TEXT function, CD TEXT can not be displayed.) 6. Do not expose the magazine to direct sunlight, the car heater or other sources of strong heat. Replace the CD magazine (CAA-355) with a new one if bent or otherwise damaged. 4 IDENTIFICATION OF PARTS 1 Installation selector levers 2 Eject button Press the eject button for ejecting the magazine. 3 Flip down door 4 CeNET terminal for input and output (13-pin) 5 Digital optical fiber output terminal 6 Address switch When connecting an CD changer and MD changer by CeNET, no more than 2 units can be connected. When both of them are CD, the address switch needs to be reset so that the address switch number is not the same for each. 1. Rotate and change the switch using a fine-tipped screwdriver. 2. Rotate the switch until it clicks into position. 6 SYSTEM EXAMPLE Installation Procedure 1. Use the double seamed hexagonal bolts to fix the lead clamp and installation bracket to the unit (on both sides) in the desired direction of installation. 2. Use the wing nut to hold in place the installation bracket with bolt to the installation bracket, which is attached to the unit. Then affix the cushion rubber. 9 TROUBLESHOOTING Loss of power Connection with the source unit is not recognized. Magazine cannot be loaded. “No Disc” sign appears when searching for discs. Noise, skipping Mechanism does not function. Magazine is ejected evenwhen inserted into the unit. Bad connection. The length of the CeNET cable wiring is more than 65.62 ft (20m). Address switch numbers are the same. Magazine inserted wrongly. A magazine is already in the player. Distorted magazine. Disc inserted upsidedown. Moisture or dirt on disc. The installation selector levers are set to different positions on both sides. The unit installation direction and the installation selector lever positions do not match. Disc bent or badly damaged. Disc is very dirty. Mechanical error. Disc holder is not correctly inserted into the magazine. Check connections. Connect the cable again. Rewire the connection so that the length of cable is less than 65.62 ft (20m). When the 2 CD changers are connected, set the address switch so that they do not have the same address number. Refer to the “Example of address switch setting” in the section titled “IDENTIFICATION OF PARTS”. Insert correctly. Eject the magazine and insert the other. Buy New Magazine CAA-355. Read the section on “Inserting The CD” carefully and reinsert the CD correctly. Wipe disc free of moisture and dirt. Set the installation selector levers to the same position on both sides. Set the unit installation direction and the installation selector lever positions to match each other. When installed at an angle, change the installation selector lever to a position (H, 45°, V) not prone to noise or sound loss. Compare with another disc. If bad, discard the damaged disc. Clean the disc. 1. Referring to section “INSTALLATION”, check the three angle of installation selector levers are properly set. If not, set them at the proper position for the angle of installation. 2. Check whether The CD magazine can be ejected by pressing the CD magazine eject button, then insert a new CD magazine. Read the section on “Inserting the CD” carefully and reinsert the disc holder correctly. lf the same phenomenon still occurs after checking ...
)
