Évaluations - 2, GPA: 3.5
(
)
)
|
Facilité d'utilisation
Time and audio source name flash alternately. 3 Within 6 seconds, press for gto designate the timer-on time, then press a. Pressing either button changes both the hour and the minute. Holding it down will vary the time rapidly by 10-minute interval, and pressing it repeatedly will vary by 1 minute interval. 4 Within 4 seconds, press for gto select the duration for the timer-activated period. The duration can be set between 5 and 240 minutes in 5 minute steps. The duration will be automatically set after 4 seconds. It will also be set if ais pressed within 4 seconds after step 4. 5 Adjust the volume. The source sound will play at the volume level set in this step when the power is turned on by the timer. If the volume level is set to 17 or higher, however, it will automatically be set to 16 when the power is turned on. 6 Prepare the source. To listen to a CD, load the disc to be played first on tray 1. To listen to a tape, insert the tape into deck 1 or 2. To listen to the radio, select the band and tune in to a station. 7 Press POWER to turn off the power. When the timer-on time is reached, the unit turns on and begins play with the selected source. 8 Get ready for the tape function or the timer recording. To listen to the tape, press c on deck 1 or 2. To record the source, press w on deck 1. When the timer-on time is reached, the unit turns on and begins play with the selected source. While the timer is in operation, the display indication is dimmer than usual. TIMER RECORDING You can change the source that was selected in step 1 by pressing one of the function buttons before pressing ain step 3. The timer recording period and tape length When the length of the tape to be recorded is shorter than the timer recording period, w on deck 1 is released before the timer is off. When the tape length is longer than the timer recording period, w is not released. If w is not released for a long time, the tape in the deck may be damaged. Press Zto release w. To check the timer setting Press TIMER while pressing SHIFT on the remote control. The timer-on time, the selected source, and the duration for the timer-activated period will be displayed for 4 seconds. En To change any of the previous setting Carry out from step 1. However, if you do not change the timer-on time, in step 3 just press a twice and continue from step 4. To cancel the timer standby mode temporarily Press TIMER repeatedly while pressing SHIFT on the remote control so that 5 disappears. To restore the timer standby mode, press again to display 5. Using the unit while the timer is set You can use the unit normally after setting the timer. Before turning off the power, check whether the contents in step 5 and 6 are set as you wish, turn off the power and carry out step 8 if necessary. • Timer playback and timer recording will not begin unless the power is turned off. • Connected equipment cannot be turned on and off by the built in timer of this unit. Use an external timer. • If the timer recording is done with the economizing mode (page 6) set to “ECO ON” or “ECO AUTO” and the power turns off, the dimmer mode will be set to “DIMMER 3” and the volume level will be 0 (minimum level) the next time the power is turned on. • You can check the timer setting by pressing TIMER while pressing SHIFT on the remote control even while the power is off. In this case, if you press awithin 4 seconds after pressing TIMER while pressing SHIFT on the remote control, you can enter the timer setting mode and change the previous setting. ENGLISH 15 SETTING THE SLEEP TIMER DEMO (Demonstration) OTHER FEATURES SETTING THE SLEEP TIMER DEMO (Demonstration) OTHER FEATURES The unit can be turned off automatically at a specified time. Use the remote control. 1 Press SLEEP while pressing SHIFT. 2 Within 4 seconds, press for gto specify the time until the power is turned off. The time changes between 5 and 240 minutes in 5-minute steps. Specified time While the timer is in operation, the display indication is dimmer than usual. To check the time remaining until the power is turned off Press SLEEP once while pressing SHIFT. The remaining time is displayed for 4 seconds. To cancel the sleep timer Press SLEEP twice while pressing SHIFT so that “SLEEP oFF” appears on the display. You can enjoy two kinds of DEMO modes on this unit. One is demo, the other one is game demo. In the demo mode, colorful illumination demonstrates in the display. In the game demo mode, you can play a game. To switch the two modes to each other, press POWER while pressing c when the power is off. To activate the demo or the game demo, press cwhen the power is off. To deactivate the demo or the game demo, press a. To play the game demo 1 To start the game demo, press c when the power is off. Three numbers on the display start to run. 2 Press s once. The number on the left side stops. 3 Press s twice to stop the remaining two numbers. Scoring: 20 points are given to start the game. If all the numbers are equal, 50...