Évaluations - 1, GPA: 3
(
)
)
|
Facilité d'utilisation
Also, the "Flip-Flop" function can work with the cd player connected directly to speakers, without the mixer. With “Flip-Flop™” you can have one disc drive begin playback when the other ends. You can “Flip Flop™” single tracks, or entire discs. NOTE: When the cd player is connected directly to the speaker, without a mixer, the player can only "Flip-Flop" in single mode. It cannot "Flip-Flop" entire discs. To "Flip-Flop" entire discs, the player must be connected to a mixer. FLIP-FLOP™ connection and set-up using a mixer: 1) Connect your system as described under ""FLIP-FLOP" (RELAY) CONNECTED TO A "Q" START MIXER" on the next page. 2) Turn the "Q" Start functions on your mixer to "on", and set your American Audio® “Q” Deck™ mixers' crossfader to the center position. 3) Load disc drives with audio discs. 4) Press the RELAY BUTTON (12), the LED above the RELAY BUTTON will light up letting you know that Flip-Flop™ mode has been activated. Press the SGL/CTN BUTTON (7) to choose between SINGLE mode or CONTINUOUS mode. 5) After they have both cued, press the PLAY/PAUSE BUTTON (17) on one of your drives to begin playback. 6) If you have the cd player set to SINGLE mode, the first cds' single track will play and after it has ended the second cds' track will immediately begin playback. If the player is set to CONTINUOUS mode, the first cd will play all the way through, and then after it has ended the second cd will start. 7) FLIP FLOP™ will continue until you stop it or power is interrupted. 8) To deactivate Flip-Flop™ mode, press the RELAY BUTTON again. FLIP-FLOP™ connection and set-up direct to speakers: 1) Connect your system as described under ""FLIP-FLOP" (RELAY) CONNECTED DIRECT TO SPEAKERS" on the next page. 2) Connect CONTROL START UNIT 1 to CONTROL START UNIT 2 on the back of the remote con- troller. 3) Load disc drives with audio discs. 4) Press the RELAY BUTTON (12), the LED above the RELAY BUTTON will light up letting you know that Flip-Flop™ mode has been activated. Press the SGL/CTN BUTTON (7) to choose SINGLE mode. The "Flip-Flop" function, when connected in this way cannot "Flip-Flop" entire cds. 5) After they have both cued, press the PLAY/PAUSE BUTTON (17) on one of your drives to begin playback. 6) Once the first cds' single track has ended the second cds' track will immediately begin playback. 7) FLIP FLOP™ will continue until you stop it or power is interrupted. 8) To deactivate Flip-Flop™ mode, press the RELAY BUTTON again. ©American Audio® --DCD-PRO310™ Instruction Manual Page 18 "FLIP-FLOP" SET UP INSTRUCTIONS TIME PITCH S G L C T N TIME PITCH S G L C T N PROG. SINGLE TOTAL REMAIN TRACK M S F PROG. SINGLE TOTAL REMAIN TRACK M S F SERIAL NO: MODEL NO : Q-2422 POWER SOURCE : 115/230V~ 50/60Hz 13W MKII MADE IN CHINA MIN MAX TRIM OUTPUT B A BOOTH AUX/IN "FLIP-FLOP" (RELAY) CONNECTED DIRECT TO SPEAKERS TIME PITCH S G L C T N TIME PITCH S G L C T N PROG. SINGLE TOTAL REMAIN TRACK M S F PROG. SINGLE TOTAL REMAIN TRACK M S F "FLIP-FLOP" (RELAY) CONNECTED TO A "Q" START MIXER ©American Audio® - - DCD-PRO310™ Instruction Manual Page 19 BEFORE SWITCHING OFF THE POWER • When you have finished using the CD unit, and before switching off the power, be sure that the disc holder has been closed with the OPEN/CLOSE button. • TRAY PROTECTION: If tray is not closed after 60 seconds, it will close automatically and pause. CAUTION: DO NOT forcibly close the disc holder when the power is off. Do not switch off the power when the disc holder is open. Switch off the power after the disc holder has been closed with the OPEN/CLOSE button. DO NOT switch off the power when the disc holder is open. Switch off the power after the disc holder has been closed with the OPEN/CLOSE BUTTON. COMPACT DISCS 1. PRECAUTIONS ON HANDLING COMPACT DISCS Compact disc are constructed of the same types of plastic record are. To avoid severe damage to you valuable disc please observe the following guide lines. Following the these guide lines will ensure long disc life. • Do not allow fingerprints, oil or dust to get on the surface of the disc. If the disc is dirty, wipe it off with a soft dry cloth. • Do not use benzene, thinner, water, record spray, electrostatic-proof chemicals, or silicone-treated cloths to clean discs. • Always handle discs carefully to prevent damaging the surface; in particular when removing a disc from the jewel case. • Do not bend the disc. • Do not apply heat. • Do not enlarge the hole in the center of the disc. • Do not write on the label (printed side) with a hard tipped implement such as a pencil or ball point pen. • Condensation will form if a disc is brought into a warm area from a colder one, such as outdoors in winter. Do not attempt to dry the disc with a hair dryer, etc. 2. PRECAUTION ON STORAGE • After playing a disc, always unload it from the unit. • Always store the compact disc in the jewel case, protecting from dirt or damage. • Do not place discs in the follo...