Évaluations - , GPA: ( )

Instructions Audiovox, Modèle ACC-56

Fabricant : Audiovox
Taille : 269.44 kb
Nom Fichier : 5b2f9e2b-3c2f-4d43-8215-7b15293e046e.pdf

Langue d'enseignement:

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

Select the desired mounting area on your car dashboard that will allow ease of use and full visibility of the LCD display. Peel off the protective paper on the adhesive pad. Make certain the dash area is clean of all wax, grease, etc., and press the remote control in place. Allow a 1/2 hour for the adhesive to secure, then you will find the Velcro pads will allow you to remove the remote control for hand-held use if desired and replace it as often as needed. MOUNTING THE FM MODULATOR There are two mounting tabs on the FM modulator. It can be secured by two methods. Use two screws “C” and drill two 3/32" holes or use electricians tape or twist ties (not provided). ADJUSTMENT OF FM MODULATOR TUNING To operate your ACC-56, your car radio must be first tuned to the FM band at 89.1MHz. If you find interference on this frequency, you can change the output frequency from the FM module to 88.7 MHz., by moving the slide switch on the FM modulator to the 88.7 MHz. position. You will then have to tune your radio to 88.7 MHz instead of 89.1 MHz, when using your CD changer. CAR DASHBOARD CLEAN MOUNTING AREA REMOTE CONTROL REMOVE PAPER LINER DRILL TWO AND PRESS IN PLACE 3/32" DIA. HOLES MOUNTING SLIDE SURFACE SWITCH SCREW "C" (2 PCS.) FM MODULATOR AUDIO LEVEL ADJUST FM MODULATOR REMOTE CONTROL OPERATING INSTRUCTIONS Upon inserting a loaded CD magazine into the changer, the unit will begin automatically checking the magazine for the number of discs loaded and their locations. This will occur even if the vehicle’s ignition is turned off. This process will take approximately 45 seconds. During this time, the remote control function will be inoperative. CONTROLS 10 2 1 3 5 4 6 7 8 9 LCD Display Track/Disc Scan (SCN) Track/Disc Repeat (RPT) Track/Disc Shuffle (SFL) Reset Button Play/Pause ( / II) Power Off Switch (OFF) Track (TRK) Select ( ) Track (TRK) Search ( ) Disc Select ( +/-) PREPARING FOR OPERATION 1. Load CD magazine and insert into changer as described on page 16. 2. Turn on your car ignition and your car stereo and select “FM” band . 3. Tune to 89.1 on the FM band unless you set the selection switch on the FM module to 88.7; then tune to 88.7 on the FM band. NOTE: You may find that it will be easier to use one of your presets specifically for CD operation. 4. Press the Reset button on the remotecontrol using a pencil tip or other thin pointed instrument. NOTE: This is only required the First Time you use the Changer. 5. Turn on the CD changer by pressing the Play/Pause button . The LCD panel will illuminate and disc number 1 will begin play. 6. Adjust your car radio’s volume, balance and tone controls for desired sound. 7. When the last track on disc 1 has played, the unit will automatically advance to the next disc in sequence and begin playing. This will continue until all discs have been played at which time the unit will begin playing disc number 1 again. 2 4 8 3 6 5 10 1 9 7 12 13 14 11 FM 89.1 17 16 15 USE OF CONTROLS LCD DISPLAY The LCD Display Panel will illuminate when the CD changer is operating. Different symbols will appear depending on the function and operation in use. Each functional display is explained in the following paragraphs. TRACK/DISC SCAN (SCN) When the Scan button is pressed, the indication SCN will appear on the LCD panel and the first 10 seconds of each track on the disc will be played in order. When a desired track is reached, press the Scan button again and play of that track will continue (SCN will disappear from the display). Scan mode will be cancelled by activating any other function (Repeat, Shuffle, Disc Select, Track Select, or Track Search). When the Scan button is pressed and held for longer than 2 seconds, the SCN and DISC indications will appear on the LCD panel and the first 10 seconds of the first track of each disc in the magazine will be played. When a desired disc is reached, press the Scan button again and play of that disc will continue (SCN and DISC will disappear from the display). Disc Scan mode will also be cancelled by activating any other function (Repeat, Shuffle, Disc Select, Track Select, or Track Search). TRACK/DISC REPEAT (RPT) When the Repeat button is pressed, the indication RPT will appear on the LCD panel and play of the selected track will be continuously repeated until the Repeat mode is cancelled by pressing the Repeat button again or by activating the Scan 9 or Shuffle 7 functions. When the Repeat button is pressed and held longer than 2 seconds, the RPT and DISC indications will appear on the LCD panel and play of the selected disc will be continually repeated until the Disc Repeat mode is cancelled by pressing the Repeat button again or by activating the Scan 9 or Shuffle 7 functions. TRACK/DISC SHUFFLE (SHF) When the Shuffle button is pressed, the indication SHF will appear on the LCD panel and the tracks on the disc will be played in a random, shuffled order. The Track Skip 5 function will also select tracks in the shuffled order instead of t...