Évaluations - , GPA:
(
)
)
Fabricant : Audiovox
Taille : 524.73 kb
Nom Fichier : 0882c0e9-069b-42ab-b9be-648e59ce7e0f.pdf
Langue d'enseignement: 
Le document est chargé, s'il vous plaît patienter
 |
Le document est chargé, s'il vous plaît patienter
Facilité d'utilisation
The tape will keep out dust, which could cause the unit to malfunction. HORIZONTAL INSTALLATION VERTICAL INSTALLAITON 45° ANGLE INSTALLATION Set the 2 anti-vibration springs to Set the 2 anti-vibration springs to Set the 2 anti-vibration springs to position "0". position "90". position "45°". ANTI-VIBRATION SPRINGS POSITION PROCEDURE FOR HORIZONTAL INSTALLATION W/O STUDS 1 Attach a bracket to each side of the unit, using the machine screws with integral flat and lock washers (M4 x 10). In the horizontal position, use bracket mounting holes 1 and 1' as shown at the right. Set anti-vibration springs to position "0" as shown above. NOTE: Use masking tape to cover unused mounting holes on sides of unit. . . . . . . MACHINE SCREW WITH FLAT AND LOCK WASHERS (M4 x 10) 2 Determine unit mounting location, and drill four mounting holes. Never mount the unit near the fuel tank. DRILL HOLES 4MM IN DIAMETER 3 Secure the unit in place, using four self-tapping screws (M5 x 12). Use RTV (silicone sealer) on screw threads and around the holes to prevent moisture intrusion. BRACKET (Left Side) BRACKET (Right Side) SELF-TAPPING SCREWS (M5 x 12) PROCEDURE FOR VERTICAL INSTALLATION W/O STUDS Note If the anti-vibration spring position has been changed and verified for vertical mounting (as shown on page 4), start with step 2. 4 2 Mount the unit in place, using four self-tapping screws (M5 x 12). Use RTV (silicone sealer) on screw threads and around the holes to prevent moisture intrusion. Determine the mounting location, and drill four mounting holes. 3 1 Never mount the unit near the fuel tank. DRILL HOLES 4MM IN DIAMETER SELF-TAPPING SCREWS (M5 x 12)BRACKET (Left Side) BRACKET (Right Side) Attach bracket to each side of the unit, using machine screws with integral flat and lock washers. (M4 x 10). In the vertical position, use holes 2 and 2' as shown at left. NOTE: Use masking tape to cover unused mounting holes on sides of unit. MACHINE SCREWS w/WASHERS (M4x10) BRACKET (Right Side) BRACKET (Left Side) Set the 2 anti-vibration springs to position "90". PROCEDURE FOR 45° ANGLE INSTALLATION W/O STUDS Note If the anti-vibration spring position has been changed and verified for 45° angle mounting (as shown on page 4), start with step 2. Determine the mounting location, and drill four mounting holes. 4 2 Mount the unit in place, using four self-tapping screws (M5 x 12). Use RTV (silicone sealer) on screw threads and around the holes to prevent moisture intrusion. 3 1 Never mount the unit near the fuel tank. MACHINE SCREW WITH FLAT AND LOCK WASHERS (M4 x 10) DRILL HOLES 4MM IN DIAMETER SELF-TAPPING SCREWS (M5 x 12) BRACKET (Left Side) BRACKET (Right Side) BRACKET (Left Side) BRACKET (Right Side) Attach bracket to each side of the unit, using the machine screws with flat and lock washers (M4x 10). In the 45 position, use holes 1 and 3' as shown at left. Set the 2 anti-vibration springs to position "45°". NOTE: Use masking tape to cover unused mounting holes on sides of unit. PROCEDURE FOR CHANGER INSTALLATION USING MOUNTING STUDS Note: Make sure the anti-vibration spring position has been changed and verified for the proper angle mounting (as shown on page 4). 1 Determine mounting location. If unit is to be installed onto mounting studs located under carpet, lift carpet to expose metal chassis and mark position of each stud as shown below in detail A and B. 2 Insert two hexagonal mounting bolts through underside of each bracket (detail A) and mount stud bracket in position using two self-tapping screws into metal chassis. Hex bolt heads should be flush with underside of stud bracket. 3 Replace carpet over bracket studs (detail B), mark position of stud end of each bolt, and cut holes in carpet so bolts protrude through carpet. 4 Proceed with unit mounting by positioning unit mounting brackets over protruding hex bolts as shown in details C, D and E. Secure mounting brackets to bolts using hex lock nuts. 5 If mounting studs are to be located directly on mounting surface with no carpet in between, mount changer directly on studs as illustrated below in details A, C, D and E. HEX BOLT (M6 x 15) CARPET SELF-TAPPING SCREWS (M5 x 12) STUD BRACKET CHASSIS STUD BRACKET STUD BRACKET MOUNTING ARRANGEMENT (Detail A) STUD BRACKET MOUNTING UNDER A CARPET (Detail B) VERTICAL INSTALLATION SUSPENDED INSTALLATION HORIZONTAL INSTALLATION WITH STUD BRACKET WITH STUD BRACKET WITH STUD BRACKET (Detail C) (Detail D) STUD BRACKET STUD BRACKET CHANGER MOUNTING BRACKET CHANGER MOUNTING BRACKET HEX NUT (M6) HEX NUT (M6) HEX NUT (M6) STUD BRACKET CHANGER MOUNTING BRACKET (Detail E) VEHICLE WIRING Mating 8-pin DIN socket on rear of compatible radio chassis (see note 1 below). DIN cable(8-pin) CD changer Car Stereo with CD Changer Controls NOTE: 1. Check with your Audiovox car audio dealer to be sure your stereo is directly compatible with this CD changer. 2. Wiring instructions for use with FM Modulator/ Commander Systems are included with the CDC-MC1, CDC-MCR2...