|
Par ce dispositif a également d'autres instructions :
Facilité d'utilisation
The program can contain up to 24 tracks (a pause inserted between tracks is counted as one track). Note that tracks whose numbers are over 24 cannot be programmed automatically. EDIT/TIME FADE ·0 / ) 1 Press EDIT/TIME FADE before you start playing until EDIT appears and “A” in the indication flashes in the display. 2 Press 0 or ) to specify the tape length. Each time you press these buttons, the display changes as shown below, with the tape length of one side following each indication. n HALF . C-46 . C-54 . C-60 . C-74 . C-90 . - -. - -N (23.00) (27.00) (30.00) (37.00) (45.00) When you select “HALF” The player sets the program of each side to a half of the total playing time of the disc. Note that you cannot select “HALF” when the disc has more than 24 tracks. 3 Press EDIT/TIME FADE to have the player create the program. The display shows the tracks to be recorded. “B” in the indication flashes in the display. 4 When you record on both sides of the tape, press EDIT/TIME FADE again. The player inserts a pause, then creates the program for side B. The display shows the programmed tracks. When you record on one side of the tape or on a DAT or MD, skip this step. 5 Start recording on the deck and then press · on the player. When you record on both sides of the tape, the player pauses at the end of the program for side A. 6 When you record on side B, reverse the tape and press · or P on the player to resume playing. To cancel Time Edit Press PLAYMODE until “SHUFFLE” and “PROGRAM” disappear from the display. When using the remote, press CONTINUE (CDP-XE500 only). You can program the tracks you want in advance Select the tracks before doing the above procedure. The player creates a program from the remaining tracks. In this case, you cannot select “HALF” to specify the tape length. You can freely specify the tape length Set the tape length using .AMS ±. Example: When the tape length of one side is 30 minutes and 15 seconds 1 To set the minutes, turn . AMS ± until “30” appears in the display, then press ENTER . 2 To set the seconds, turn . AMS ± until “15” appears in the display, then press ENTER . When tracks, which aren’t numerically consecutive on the disc, are programmed consecutively (i.e. 1, 3, 5 etc.) A one-second access time blank is added between the tracks. To check and change your program See page 11. Recording FromCDsRecording From CDs Fading In or Out You can manually fade in or out to prevent tracks from starting or ending abruptly. Note that you cannot use this effect when you use the DIGITAL OUT (OPTICAL) connector (for CDP-XE500). Fading in or out at the point you want (CDP-XE500 only) Z FADER To Press FADER Start play fading in During pause. The Q indication flashes and play fades in. End play fading out When you want to start fading out. The q indication flashes. The play fades out and the player pauses. Fading time lasts for 5 seconds. If you press FADER during Music Scan (page 8), fading time changes to 2 seconds. Fading out at the specified time (Time Fade) You can have the player fade out automatically by specifying the playing time. Once you set the Time Fade, it works twice, that is, the play fades out at the end of both sides of a tape. EDIT/TIME FADE ·0 / ) 1 Press EDIT/TIME FADE repeatedly before you start playing until “ ” and “A” in the indication appear in the display. 2 Press 0 or ) to specify the playing time. Each time you press these buttons, the display changes as shown below, with the playing time of one side following each indication. n HALF . C-46 . C-54 . C-60 . C-74 . C-90 . - - .- -N (23.00) (27.00) (30.00) (37.00) (45.00) When you select “HALF” The player sets the playing time to a half of the total playing time. 3 Press · to start playing. At the specified time the play fades out and the player pauses. “B” in the indication appears in the display. 4 To record on side B, reverse the tape and press · or P on the player to resume playing. Again, the play fades out at the specified time. To cancel Time Fade Press EDIT/TIME FADE. You can freely specify the playing time See “You can freely specify the tape length” on page 12 . You can change discs during Time Fade If the play ends before the specified fade-out time, (for example, when you record CD-singles on a tape) change the disc. The specified fade-out time is counted only during playing. You can fade in to resume playing in Step 4 (CDP-XE500 only) After you reverse the tape, press FADER on the remote. Note Time Fade will be cancelled if you press 0 or ) during the operation. Recording From CDs Additional Information Adjusting the Recording Level (Peak Search) The player locates the highest level among the tracks to be recorded to let you adjust the recording level before you start recording. PEAK SEARCHp 1 Before you start playing, press PEAK SEARCH. “PEAK” flashes in the display and the player repeats the portion of the highest level. 2 Adjust the recording level on the deck. 3 Press p on the player to stop Peak Search. ...
Ce manuel est également adapté pour les modèles :CD-joueurs - CDP-XE400 (88.65 kb)