Silde the FUNCTION selector to TAPE. 2. Insert a cassette tape. 3. Press the. PLAY button. TO STOP PLAYBAC. . Press the. STOP button. TO FAST WIN. . Press the. F.FWD or. REWIND button. . Press the. STOP button to stop winding at the desired position. RECORDIN. USE ONLY NORMAL ( TYPE I ) TAPE FOR RECORDING. 1. Insert a cassette tape. 2. Prepare the source to be recorded and play it. Recording from a C. Recording from the radi. (Refer to using the CD player. ( Refer to radio operation . . Press th

To obtain repair or replacement within the terms of this Warranty, the product is to be delivered with proof of warranty coverage ( e. g. dated bill of sale) , specification of defect(s), transportation prepaid, to the warranty center at the address shown below. This Warranty does not extend to the elimination of car static or motor noise, to correction of antenna problems, to costs incurred for installation, removal, or reinstallation of the product, or damage to tapes, compact discs, accessori

Determine the mounting location for the unit. 4. Drill holes for the self-tapping screws ( T5x12). 5. Install self- tapping screws to secure the CD changer to the metal. Installation (continua) Instalacion en Suspension 1. Asegurese que los resortes antivibracion esten colocados en la posicion " 0". 2. Adhiera el soporte (A) a cada lado de la unidad utilizando los tornillos de la maquina ( M4x5) . 3. Determine la ubicacion de montaje para la unidad. 4. Realice agujeros con el taladro para los to

should exercise extreme caution or discontinue use in potentially Portable Radio/CD Playe. FUNCTION OF CONTROLS Operating Instructio. Before operating the unit, please read this manual thoroughly an. retain it for future reference. WARNING. TO PREVENT FIRE OR SHOCK HAZARD, DO NO. EXPOSE THE UNIT TO RAIN OR MOISTURE. TO AVOID ELECTRICAL SHOCK, DO NOT OPEN TH. CABINET. REFER SERVICING TO QUALIFIED PERSONNEL ONLY. CAUTION The use of optical instruments with this product will increase eye hazard. IN

7. Left front speaker 8. Right front speaker 9. Left rear speaker 10. Right rear speaker Fuses When replacing a fuse, make sure the new fuse is the correct type and amperage. Using an incorrect fuse could damage radio. The CD3210 uses one 10 amp fuse located below the wiring connector: 10 amp fast blow ATO. Reconnect Battery When wiring is complete, reconnect the battery negative terminal. Install Half-Sleeve Instalacion de la Camisa Installation du demi-manchon 4 1 2 3 Jensen Connector 1 2 Conn

Mount the unit in place, using four self-tapping screws (M5 x 12). Use RTV (silicone sealer) on screw threads or around the holes to prevent moisture intrusion. Set the left and right anti-vibration springs to position "45°". Determine the mounting location, and drill four mount- ing holes. 1 Never mount the unit near the fuel tank. Bracket (L) Bracket (R) Hexagonal bolt with washer base (M5 x 10) Drill holes 4mm in diameter. Bracket (R) Self-tapping screw (M5 x 12) NOTE: Use seals (A) to cover

onto a disc. 1 * Do not expose the discs to direct sunlight or excessive heat. * Clean the discs before inserting them into the disc magazine. Always clean a disc from center outward with a cleaning cloth. * Never use solvents such as benzine or alcohol to clean a disc. * You cannot play an 8cm(3 inch) CD even with the specially designed adapter. Notes on the disc magazine * Do not leave the disc magazine in a place subject to excessive temperature or humidity. * Do not insert more than

Instruction Manual Jukebox with CD CR11CD RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER - SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lighting flash with arrowhead symbol, within an equilateral triangle, is intended to alert user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute risk of electric shoc

The tape will keep out dust, which could cause the unit to malfunction. HORIZONTAL INSTALLATION VERTICAL INSTALLAITON 45° ANGLE INSTALLATION Set the 2 anti-vibration springs to Set the 2 anti-vibration springs to Set the 2 anti-vibration springs to position "0". position "90". position "45°". ANTI-VIBRATION SPRINGS POSITION PROCEDURE FOR HORIZONTAL INSTALLATION W/O STUDS 1 Attach a bracket to each side of the unit, using the machine screws with integral flat and lock washers (M4 x 10). In the ho