Évaluations - 0, GPA: 0
(
)
)
|
Facilité d'utilisation
CONTROLS (see fig. 1 ) 1DISPLAY - shows the clock/ alarm time and status of the set 2ALARM indicator -lights up when alarm is activated 3Frequency indicator - shows the radio frequency of your selected waveband 4REPEAT ALARM / SLEEP OFF -switches off the active alarm for a 8-9 minute period -switches off the sleep function 5CLOCK - sets the clock time 6SLEEP -activates the radio for sleep function -adjusts the sleep period 7ALARM RESET - stops the active alarm for 24 hours 8ALARM - sets the alarm function 9RADIO / ALARM RADIO ON: switches on the radio RADIO OFF: switches off the radio/alarm ALARM -RADIO: activates the radio for alarm ALARM - BUZZ: activates the buzzer for alarm 0SET TIME HR / MIN -adjusts the hours / minutes for clock / alarm / sleep time !Power cord -connects to wall outlet @Pigtail - improve FM reception #VOLUME - adjusts the sound level $Battery door - opens to store a 9 volts 6F22 battery (not included) for clock memory backup. %FM/MW -selects FM/MW waveband ^TUNING - tunes to radio stations INSTALLATION POWER SUPPLY 1 Check if the power supply, as shown on the type plate located on the bottom of the set, corresponds to your local power supply. If it does not, consult your dealer or service center. 2 Connect the plug to the wall outlet. 3 To disconnect the set from the power supply completely, remove the plug from the wall outlet. CLOCK MEMORY BACKUP The clock memory backup allows your alarm and clock time settings to be stored for up to a day when there is a power interruption e.g. power failure. The complete clock radio and display illumination will be switched off. As soon as the power supply returns, the display will indicate the correct time. 1 Remove the battery door to insert a 9 volts 6F22 type battery (not included) for backup. 2 Replace the battery door. NOTE: If no backup battery is installed or the power interruption is prolonged, you will need to set the clock and alarm times again. Batteries contain chemical substances so they should be disposed of properly. RADIO You can use this set solely as a radio! 1 Adjust RADIO / ALARM to RADIO ON to switch on the radio. 2 Select your waveband by adjusting the FM/MW switch. 3 Adjust TUNING to tune to your desired station. 4 Turn the VOLUME control to adjust the volume level. 5 Adjust RADIO / ALARM to OFF to switch off the radio. To improve reception: FM: Extend and position the pigtail fully to obtain optimal reception. MW: uses a built-in antenna inside the set. Direct the antenna by adjusting the position of your set. SETTING THE CLOCK / ALARM TIME The time is displayed using the 24-hour clock. 1 Hold down CLOCK or ALARM. 2 Press HR or MIN repeatedly, or hold down HR or MIN to adjust minute and/or hour. 3 Release CLOCK or ALARM and HR or MIN when you reach the correct setting. ™The set clock time will show on the display and start to run. Specifications AC Power................................................................ 220 – 230 V / 50 Hz Power Consumption Active................................................................................................ 5 W Standby........................................................................................... . 2 W Dimensions (w x h x d).............................. 130.4 x 130 x 46.8 (mm) Weight ....................................................................................... .0.395 kg SELECTING THE ALARM MODE To use the alarm, you must set the alarm time first. You can choose from two different alarm modes to wake you up: by radio or buzzer. 1 Select your choice of alarm mode by adjusting RADIO / ALARM to RADIO or BUZZ. ™The alarm indicator (AL) will light up. Helpful Hint: • If you have selected the radio mode, make sure you have adjusted the volume loud enough to wake you. • The buzzer is set at a fixed volume and cannot be adjusted. SWITCHING OFF THE ALARM There are three ways of switching off the alarm. Unless you cancel the alarm completely, the 24 hour alarm reset option will be automatically selected after 1 hour and 59 minutes, from the time your alarm time first goes off. 24 HOUR ALARM RESET If you want the alarm mode to be stopped immediately but also wish to retain the same alarm setting for the following day: • Press ALARM RESET during the alarm call. ™The alarm indicator (AL) will remain on. CANCELING THE ALARM COMPLETELY To cancel the set alarm time before it goes off, or during the alarm call: • Adjust RADIO / ALARM to OFF position. ™The alarm indicator (AL) will light off. REPEAT ALARM This repeats your alarm call at 9-minute intervals. 1 During the alarm call, press REPEAT ALARM / SLEEP OFF. ™The alarm indicator (AL) will remain on. SLEEP This set has a built-in timer which enables the set to be automatically switched off during radio playback after a set period of time. This allows you to lie back, listen and fall asleep. The maximum sleep time is 1 hour and 59 minutes. Setting SLEEP 1 Set RADIO / ALARM to OFF position. 2 Set the sleep time to activ...