Évaluations - 0, GPA: 0
(
)
)
|
Facilité d'utilisation
2. Hold down or press HOUR + or MIN + repeatedly to set and adjust the hours and minutes respectively. Release HOUR + or MIN + when you have reached the correct setting. 3. After both the hours and minutes are set, press SET AL / TIME to confirm the setting. ™ You will hear two short beeps. ™ Display returns to clock time. • Time setting is also automatically confirmed after 10 seconds after you set the time. • It is not possible to adjust the alarm time during an alarm call or the repeat alarm mode. RADIO (FM only) 1 Press RADIO ON / OFF once to switch on the radio. ™ Display shows ‘ON’ shortly. 2 Adjust TUNING to find your radio station. 3 Adjust the sound using VOLUME. 4 Press RADIO ON / OFF to switch off. To improve reception: • Extend and position the pigtail fully to obtain optimum reception. RUOH NIM PM PM REPEATALARM•BRIGHTNESS CONTROL USING THE ALARM General (see 2) If you wish to use the alarm, first set the alarm time before selecting your choice of alarm mode. By rotating the set in 4 different position, you can choose Radio (FM) / Buzzer / Submarine / Frog to wake you up. As you rotate the set, AJ3136 interacts in the following way. You will : ™ hear a special whirring sound effect ™ see the backlight blink briefly. The hour and minute display will also adjust to match the new rotated position. TIP : • If you wish to deactivate or activate the whirring sound, press and hold on the HOUR + and RADIO ON / OFF buttons simultaneously. • When the batteries on AJ3136 are low, the battery low icon blinks. No blacklight and sound effects are possible. Setting the alarm 1. Press ALARM ON / OFF once to switch on the alarm. ™ lights up. 2. Rotate the set with the symbol of the alarm mode, which you wish to be woke up, facing on the top. When reach alarm setting time, Radio, Buzzer, Submarine or Frog will switch on for about 30 minutes and the alarm indicator flashes. • For Buzzer option only, your gentle wake alarm increases its beep tone frequency within seconds. Switching off the alarm 24HR ALARM RESET If you want the alarm mode to be stopped immediately but also wish to retain the same alarm setting for the following day: • Press ALARM RESET / SLEEP. ™ You will hear a sound “Ding Dong” confirming 24 hour reset activation. REPEAT ALARM This will repeat your alarm call at 5 minute intervals. • During the alarm call, press REPEAT ALARM•BRIGHTNESS CONTROL ™ The alarm indicator flashes during repeat alarm. • Repeat if desired. CANCELING THE ALARM COMPLETELY • During alarm activated or repeat alarm mode, press ALARM ON / OFF once. Alarm will be switched off completely. ™ The alarm indicator disappears. SLEEP About Sleep This set has a built-in sleep timer, which enables the radio to be automatically switched off after a set period of time. There are four sleep time options. Setting and switching off sleep 1 Press ALARM RESET / SLEEP to switch on the radio 2 Within 1 second, press ALARM RESET / SLEEP again once or more to select your sleep time. • The sleep time options: SL : 30, SL : 20, SL : 10 and OFF. ™ The Sleep indicator lights up. 3 To cancel sleep, press either: – ALARM RESET / SLEEP once or more until disappears from the display. – REPEAT ALARM•BRIGHTNESS CONTROL MAINTENANCE • If you do not intend to use set for a long time, remove the batteries. • Do not expose the set to humidity, rain, sand or excessive heat caused by heating equipment or direct sunlight. • To clean your set, use a soft damp cloth or chamois leather. Do not use cleaning products, which contain benzene, thinner, etc. as these may harm the housing. ENVIROMENTAL INFORMATION We have reduced the packaging to its minimum using only paper and cardboard. Your set consists of materials which can be recycled if disassembled by a specialized company. Please observe local regulations to dispose of packing materials, exhausted batteries and old equipment. TROUBLESHOOTING If a fault occurs, first check the points listed below before taking the set for repair. If you are unable to remedy a problem by following these hints, consult your dealer or service center. WARNING: Under no circumstances should you try to repair the set yourself, as this will invalidate the warranty. Do not open the set as there is a risk of electric shock! No sound – Volume not adjusted • Adjust the VOLUME No display backlight / display malfunction/ radio and alarm do not function – Set is in Power Low mode • Insert fresh batteries Display error / no reaction to any controls – Electrostatic discharge / Electrical interference: set too close to TV, VCR or computer. • Press the RESET hole inside battery compartment of the set with a ballpoint pen. Intermittent crackling sound during FM reception – Weak signal • Extend and position the pigtail aerial The alarm does not function – Alarm time/ mode not set • See SETTING THE ALARM TIME – Volume too low for radio • Increase the volume – RADIO not tuned to a radio station • Tune to a station Rattling sound. Is something loose ? No....