Évaluations - , GPA:
(
)
)
Fabricant : Chariot Carriers
Taille : 601.96 kb
Nom Fichier : 1e4e55d2-6873-437e-ac59-09e309186bd8.pdf
Langue d'enseignement: 
Le document est chargé, s'il vous plaît patienter
 |
Le document est chargé, s'il vous plaît patienter
Facilité d'utilisation
This would mean that the baby might come into contact with the seat of the transporter itself. Contrary to the current fitting instructions, please ensure that you fit the Chariot baby seat to the Captain XL and Corsaire XL models as follows: Follow all steps up to (and inclusive of) section 1.2.1 of the fitting instructions Then guide the tensioning strap supplied through the lateral flaps that are at the bottom towards the front and pull it very tight. The tensioning strap and flaps should be positioned in front of the vertical frame tubes, when viewed from the inside of the transporter. Centre-fitting: Place the Chariot baby seat in the transporter. Lay both the straps that are attached to the bottom of the baby seat around the tensioning strap that you have fitted, and thread the end through as shown in the illustration A. This should then give a distance of about 8 cm (3 inches) between the baby seat and the tensioning strap. Pull the baby seat upwards between the fitted telescopic tube and the front fabric assembly or the front wall of the floor pan, and place it in the internal space of the transporter. Illustration A Make sure that the front padding of the baby seat is positioned above the telescopic tube. Side-fitting: Only the baby seat strap that faces the middle is to be fastened to the tensioning strap, fitted as described above. Then the baby seat is pulled around the telescopic tube. The outside-facing baby seat strap that is between the vertical frame tube and the fabric cover should be guided around the vertical frame tube, then under the telescopic tube, and finally back up between the telescopic tube and the fabric cover. Inside view Thread through the end of the The easiest way of getting the strap as shown in the above strap tight is by pulling the end illustration and pull the strap of the strap downwards below tight. the seat. Then in both cases follow steps 1.2.2., 1.2.3., 1.2.5. and 1.2.6. of the fitting instructions. The Chariot baby seat is properly fitted when the front padding is in a near vertical position above the telescopic tube after all straps have been pulled tight. 1.2.2 Securing the baby seat to the trailer seat Connect the fastex buckles on the baby seat with their counterparts on the seat belt - for side fitting, these are the ends of the belt on the appropriate side and for centre fitting, these are the ends of the belt in the centre. Experience has shown that it helps if approximately the following overall belt length adjustment is made (measured from the point of attachment to the baby seat to the point of attachment to the trailer seat): For the models with floor pan - Captain XL, Captain and Comfort - about 12cm For all others - 15 or 16cm In the illustration, the slots for feeding through the shoulder harness described in the next section can also be seen. 1.2.3 Fitting the safety belts 1.2.3.1 On luxury models Thread the belt ends protruding from the rear of the baby seat though the fasteners on the back rests of the trailer seat, as on the illustration. The fasteners are appropriately at their lowest setting. The baby seat is properly fitted if the side of the flap for the crotch harness padding that is attached to the baby seat points towards the front of the trailer. Insert both belt ends of the shoulder harness through either the two lower or the two upper slots in the baby seat, depending on the size of the child. For side fitting, use the two NoteNote: fasteners of the appropriate (See also Chariot Owner’s side and for centre fitting, the Manual.) two in the centre. The shoulder padding can be turned over at the top so that the shoulder strap can be sufficiently shortened. If necessary, the lower connecting strap of the shoulder padding can also be unstrapped and the shoulder padding turned over there as well. For all other children, the shoulder strap can be drawn through the upper flaps of the padding to prevent the padding being able to slip to the side. Insert the crotch harness from the rear through the slot in the baby seat in front of the flap for the padding. The safety belt can now be fastened as described in the Chariot Owner’s Manual. Please note: Make sure you check all belt buckles are tight! 1.2.3.2 On standard models Then insert the fastnex insert through the elastic loop at the end of the flap for the padding. Insert the crotch harness from the rear through the slot in the baby seat in front of the flap for the padding. Insert the ring through the elastic loop at the end of the flap for the padding. Insert the shoulder harness that is on the appropriate side of the baby seat through the lower or upper slot, depending on the size of the child. Working towards the rear, Connect the insert of the insert the shoulder harness fastex buckle with its unit on through the ring of the lap belt the back rest of the trailer seat. and the corresponding slot on the other side of the baby seat. 1.2.4 Securing the lower end of the baby seat Lay the belt a...