The thumbscrews should be used to lock the shelf pilasters in place at the top of the cabinet. 4. (Use steps 4 and 5, when installing on top half.) Install your precut wire shelf pilasters to the bottom half of the cabinet first. 5. Install your tray slide pilasters using the bottom slotted holes on the pilaster, as shown in Fig. 4. Press in and down to lock into place. Use the thumbscrews to lock into place. 6. When installing a full cabinet door of tray slides, always start with the bottom

t Q Part No. Description 1 4 3203343 Wire Shelf Pilaster 2 16 6022201 Tray Slide 3 1 6022191 Tray Slide Pilaster - 2 Dr. 4 3 6022301 Tray Slide Pilaster 5 47” 9202503 Tape, Extruded READ INSTRUCTIONS COMPLETELY BEFORE INSTALLATION 1. Remove all wire shelves from door opening. Remove existing pilasters by removing the thumbscrews at the top and lifting up and off the mounting studs. 2. (Use steps 2 and 3, when installing on bottom half.) Use top slotted holes on tray slide pilaster, as sh

For the second attempt to ignite gas within the same call for heat, the control increases the ignitor temperature to the value it was on the third previous successful ignition. After ignition is successful, the control sets the ignition temperature at this value for the next 255 calls for heat, after which the control repeats the adaptive algorithm. The control is constantly making adjustments to the ignitor temperature to compensate for changes in the line voltage. The 80 VAC Silicon Nitride ig

This item is a toy for dolls only. For children ages three (3) years and older. MODEL #: NAME: 00364 Pink Rosebud, 00367 Pink Gingham Folding Doll Cradle with Hood TOOLS NEEDED: Phillips Screwdriver PARTS INCLUDED: (A) 2 - Side Panels (B) 1 - Upper Support Bar (C) 1 - Lower Support Bar (D) 6 - Bolts (E) 1 - Cradle Body (F) 2 - Washers (G) 2 - T-Nuts (H) 1 - Cradle Mattress with Sheet BEFORE YOU BEGIN ASSEMBLY: Ensure that all the parts and hardware listed above are included. If an

Attach the CRADLE BODY (E) to the UPPER SUPPORT BAR (B) using the predrilled holes, TWO BOLTS (D), TWO WASHERS (F), and TWO T-NUTS (G). Insert the bolts (with washers) through the holes on the cradle bottom, then insert them through the holes on the upper support bar, and then secure the ends of the bolts in place on the underside of the support bar using the T-Nuts. STEP 3: See PICTURE 3. Unfold the two metal supports inside of the cradle body and lock them in place by putting one side behind

Attach the PSP cradle to the dual-T tab head (A) by inserting the T-tabs into the T-slots (B). Sony PSP Cradle Instructions Step 1. Insert PSP into the cradle at a slant so that the base of the PSP comes to rest on the spring loaded support legs (C). Step 2. While firmly holding the cradle, push downward on the PSP so that the spring loaded support legs slide down. This allows enough clearance for the top of the PSP to slide under the top support clip (D). Step 3. To remove PSP from cradle f

Box 444, Salem, IN USA 47167-0444 PH: 812-883-3111 - FAX: 812-883-1819 - ASSEMBLY DIRECTIONS AND PARTS LIST FREAD ALL INSTRUCTIONS WITH CARE BEFORE STARTING THE ASSEMBLY PROCEDURE. . FFFFF YOU WILL NEED A #2 PHILLIPS SCREWDRIVER, A SLOTTED SCREWDRIVER AND A HAMMER. PARTS ENCLOSED IN HARDWARE BAG (NOTED WHEN SHOWN ACTUAL SIZE) (12) Slotted/Phillips Machine ScrewsA AAAAA (actual size) F FFFFF (4) Compression Springs B BBBBB G GGGGG (4) Spring Hangers C CCCCC (4) Gate Shoes D DDDDD (2) Moulded plas