4 25. Extension cords may be used if care is exercised in their use. 26. If an extension cord is used, its electrical rating must be as great as the rating of the appliance and not draped over the edge of the table top where it could be pulled by children or tripped over. The extension cord should be a grounded type 3 wire cord. 27. The power cord supplied must not be used on any other appliance and no other power cord should be used with the Digital Sterilizer. 28. Failure to follow de-scaling instructions may cause irreparable damage. 29. There are no serviceable parts inside the Digital Sterilizer. Do not attempt to open, service or repair the Digital Sterilizer yourself. 30. Do not touch hot surfaces. Use handles or knobs. 31. HOUSEHOLD USE ONLY SAVE THESE INSTRUCTIONS Instructions for use Please refer to the diagrams in the back of the leaflet. Before using your sterilizer for the first time (see diagram B) Remove all items from inside the sterilizer body. 1. Measure exactly 90 ml of distilled water and pour in. 2. Assemble the blue components (baskets, stem and bottle rack) and place into the sterilizer. Put the lid on. 3. Connect the power cord into the back of the sterilizer and plug into the electrical outlet. 4. The unit will display a flashing ‘0’ to indicate you need to select a mode. One short press of the control button will display a flashing ‘1’. Hold the control button in for 2 seconds then release, and a rotating ‘0’ is displayed. Mode 1 is now in progress. 5. After the water has reached 100°C, it will turn to steam. When the sterilizing cycle is almost complete a numerical countdown will be displayed (see ‘Electronic Display Guide’). 6. At the end of the cycle the unit will beep 5 times. Three bars will flash and then remain displayed. 7. Let the sterilizer cool down for 3 minutes. Unplug from electrical outlet and remove power cord from the back of the sterilizer. 8. Remove the blue components and empty any remaining water from the unit. Wipe dry. The sterilizer is now ready for use. Sterilizing in Mode 1 – 6 hour sterile period Sterilizing in Mode 2 – 24 hour sterile period (see diagram C) To sterilize up to six 4 oz / 125 ml, 9 oz / 260 ml or 11 oz / 330 ml AVENT Bottles Before each use, wash items to be sterilized in mild soapy water, and rinse. 1. Measure and pour in exactly 90 ml of water if selecting Mode 1 OR 200 ml of water if selecting Mode 2. 2. Slide the lower basket onto the central stem. Thread 2 screw rings onto the central stem. Slide the bottle rack down the central stem, with the neck facing down, until it rests on the top screw ring. 3. Place the nipples through the center of the holes in the bottle rack onto the lower basket. Thread 4 screw rings onto the central stem. 4. Place inverted bottles in the bottle rack and push the upper basket onto the central stem until it rests on the catch. Place dome caps and tongs into the upper basket. 5. The upper basket is not required when sterilizing 11 oz / 330 ml bottles. 6. Place the assembled unit into the sterilizer body and put the lid on. Put the power cord into the back of the sterilizer body and plug into the electrical outlet. A flashing ‘0’ will appear, indicating that you need to select a mode. 7. To select Mode 1, press the control button once and the mode number will be displayed. To run this mode, hold the control button in for 2 seconds, then release. A rotating ‘0’ will be displayed. Mode 1 is now in progress. OR To select Mode 2, press the control button twice and the mode number will be displayed. To run this mode, hold the control button in for 2 seconds, then release. Three ascending and descending bars will be displayed. Mode 2 is now in progress. 8. Do not remove the lid until the 6 minute sterilizing cycle has ended. This is indicated by 5 beeps and 3 bars being displayed. It is recommended to let the sterilizer cool down for 3 minutes after the sterilizing cycle has been completed. Items will remain sterile for up to 6 hours provided the lid is not removed. After 2 hours, the display will show 2 bars and, after a further 2 hours, one bar. To indicate the end of Mode 1 or 2, the unit will sound a long beep followed by a flashing ‘0’ †. At this point items should be used immediately or re- sterilized. (Please refer to ‘To remove sterilized items after a cycle’.) Unplug from electrical outlet and remove power cord from the back of the sterilizer. Pour away any remaining water, rinse out the inside of the sterilizer body and wipe dry. † The end of a cycle is 6 hours after commencement of Mode 1 and 24 hours after commencement of Mode 2. The unit can be completely stopped at any time during a cycle, by pressing and holding in the control button for 2 seconds. The unit will beep and a flashing ‘0’ will be displayed, indicating the unit has returned to selection mode. To load the Philips AVENT Manual Breast Pump (see diagram D) Before each use, wash items to be sterilized in mild soapy water, and rinse. 1. Disass...