Évaluations - 3, GPA: 4.3
(
)
)
|
Facilité d'utilisation
MALAYSIA: Diimport & Diedarkan Oleh: Mattel SEA Ptd Ltd. (993532-P) Lot 13.5, 13th Floor, Menara Lien Hoe, Persiaran Tropicana Golf Country Resort, 47410 PJ. Tel: 03-78803817, Fax: 03-78803867. WARNING To prevent serious injury from falls and being strangled in the restraint system: • Always use the restraint system. • Not recommended for children who can sit up by themselves (6 months approximately, until 9 Kg/20 lbs). • Never leave child unattended. • It is dangerous to use this product on an elevated surface. • Never use toy bar as a handle. Care The pad and toys are machine washable. Wash them separately in cold water on the gentle cycle. Do not use bleach. Tumble dry separately on low heat and remove promptly. The frame and toy bar can be wiped clean using a mild cleaning solution and a damp cloth. Do not immerse this product. To remove the pad: • Lift the seat bottom tube and remove the pad lower pocket. • Push the restraint belts back through the pad. • Turn the product face down. Unfasten the buckle, and turn the product upright again. • Slide the pad upper pocket off the seat back tube. To re-assemble the pad: • Refer to assembly steps 8 and 9. CAUTION This package contains small parts in its unassembled state. Adult assembly is required. • Please read these instructions before assembly and use of this product. • Adult assembly is required. • Tool required for assembly: Phillips screwdriver (not included). • Requires four “C” (LR14) alkaline batteries for operation(not included). • Weight Limit: 9 kg (20 lbs). IMPORTANT! The maximum weight limit for this product is9 kg (20 lbs). If your child weighs less than 9 kg (20 lbs), but is really active and appears to be able to climb out of the swing, immediately discontinue its use. • Product features and decoration may vary from photo. ©2009 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.. PRINTED IN CHINAFisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, New York 14052, U.S.A. M6711b-0726 2 3 Assembly Parts IMPORTANT! Before assembly and each use, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken. Contact Mattel for replacement parts and instructions if needed. Never substitute parts. IMPORTANT! Please remove all parts from the package and identify them before assembly. Some parts may be packed in the pad. Back Leg Front Leg 2 Swing Frames Hint: To allow the productto swing properly, the swing arm-to-frame (with power switch) connection is designed to be loose. 1 • Slide the front and back legs on the swing frame out until they “click” into place. • Repeat this procedure to open the other swing frame. Toy Bar Seat Pad Press Buttons on Front Legs Seat Frame 2 Toys Base Tube 2 Base Tubes 2 • While pressing the buttons on each front leg, insert the front legs into the base tube. • Push the front legs down into the base tube until the buttons “click” into place. #6 x 2,5 cm Screw – 2 Shown Actual Size Note: Tighten or loosen all screws with a Phillips screwdriver. Do not over-tighten the screws. Assembly PULL UP PULL UP Base Tube Base Tube 3 5 • While standing on the base tube, pull the front legs up. The front legs should remain secured to the base tube. If you can remove the front legs, you have not assembled them correctly to the base tube. Re-read and repeat assembly step 2. • While standing on the base tube, pull the back legs up. The back legs should remain secured to the base tube. If you can remove the back legs, you have not assembled them correctly to the base tube. Re-read and repeat assembly step 4. Seat Hubs Seat Frame Press Buttons on Back Legs Base Tube Frame Hubs 4 • While pressing the buttons on each back leg, insert the back legs into the remaining base tube. • Push the back legs down into the base tube until the buttons “click” into place. 6 • Position the seat frame so that the tubes are upright, as shown. • While gently pulling the seat hubs out, fit them to the matching frame hubs. Hint: If the hubs do not fit together, simply turn the seat frame around and try again! Assembly Pad Lower Pocket Seat Hub 7 Seat Hub Seat Bottom Tube 9 • Insert a screw through the outside of each seat hub. Tighten the screws. • Fit the pad lower pocket onto the seat bottom tube, as shown. Pad Upper Pocket Toy Bar Seat Back Tube Slots Waist Belt Socket 10 • Insert and “snap” the peg on the toybar into the socket on the swing arm. Pull the toy bar up to be sure it is secure. • Fit the toy strings up through the slots in the toy bar leaf. Assembly is now complete. 8 • Fit the pad upper pocket over the seat back tube. • From behind the assembly, insert the waist belts through the slots in the pad. Battery Installation Battery Safety Information In exceptional circumstances, batteries may leak fluids that can cause a chemical burn injury or ruin your product. To avoid battery leakage: • Do not mix old and new batteries or batteries ...