Évaluations - 2, GPA: 3.5
(
)
)
|
Facilité d'utilisation
Adult assembly is required. CAUTION M5 x 113/16" Screw - 2 M5 Lock Nut - 2 M6 x 15/8" Screw - 8 M6 Lock Nut - 8 ALL SHOWN ACTUAL SIZE Spring - 4 Parts 3 Base Pad Metal Canopy Stay 3 Toys (Toys may be different than shown.) 2 Base Wires ® ® 2 Covers Plastic Mesh Cover Stay This product contains small parts in its unassembled state. Adult assembly is required. CAUTION M5 x 113/16" Screw - 2 M5 Lock Nut - 2 M6 x 15/8" Screw - 8 M6 Lock Nut - 8 ALL SHOWN ACTUAL SIZE Spring - 4 Assembly 4 • Open the base and position it upright on a flat surface, as shown. • Locate the end of the base with the mesh cover. Insert the entire plastic mesh cover stay into one of the button holes in the mesh cover. • Be sure to tuck the plastic mesh cover stay away from the button hole in the mesh cover. IMPORTANT! Before each use or assembly, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken. Contact Fisher-Price® for replacement parts and instructions if needed. Never substitute parts. • Position the ends of the frame tubes against the middle 1 holes in a frame. 3 Base Mesh Cover Button Hole Plastic Mesh Cover Stay • Insert the metal canopy stay through the canopy tunnel. • Insert an M6 x 15/8" screw through each frame tube and into the frame. • Fit an M6 lock nut (with the rounded side toward the fabric) into each middle, hexagonal opening on the back of the frame. 2 Metal Canopy Stay Canopy Tunnel Frame Tubes Middle Hole Middle Hole Frame M6 Lock Nut Push Base Up Frame Tube Frame Tube Frame M6 x 15/8" Screw - 4 M6 Lock Nut - 4 Rounded Side 4 Hint: You may find it easier to access the hexagonal opening on the back of the frame if you push the base up, so that the fabric is out of the way. Assembly 5 • Tighten the screws with a Phillips screwdriver.Do not over-tighten. • Repeat assembly steps 3 - 5 to attach the other ends of the frame tubes to the frame on the other side of the base. 5 • Position the base wires around the base so that the ends point upward and are against the lower holes in a frame. • Place a spring onto an M6 x 15/8" screw. • Insert the M6 x 15/8" screw with spring through a base wire and into the frame. Base Wire Lower Hole Spring Frame Base Wire M6 x 15/8" Screw - 4 Spring - 4 6 • Fit an M6 lock nut (with the rounded side toward the fabric) into each lower, hexagonal opening on the back of the frame. • Tighten the screws with a Phillips screwdriver.Do not over-tighten. • Repeat this procedure to attach the other ends of the base wires to the frame on the other side of the base. Frame 7 Rounded Side M6 Lock Nut - 4 Assembly 6 • Fasten the pad fasteners to the base fasteners. • Lift the canopy. • Attach the toys to the canopy fasteners. IMPORTANT! Assembly is now complete, but Bounce ‘n Play Activity Dome is not ready for use. Please refer to the Use instructions, on this page, beginning with step 2. ® Pad Fastener Toys Canopy Fasteners 9 • Position one end of the metal canopy stay against the upper hole in a frame. • Insert an M5 x 113/16" screw through the hole in the cover. • Fit the end of the screw through the hole in the metal canopy stay and into the upper hole in the frame. • Push on the cover to insert and “snap” the tab on the cover into the slot in the frame. Make sure you hear a “snap”. • Fit an M5 lock nut (with the rounded side toward the fabric) into the upper hexagonal opening on the back of the frame. • Tighten the screw with a Phillips screwdriver. Do not over-tighten. • Repeat this procedure to attach the other end of the metal canopy stay and the remaining cover to the frame on the other side of the base. Upper Hole Cover Slot Tab Metal Canopy Stay M5 x 113/16" Screw -2 M5 Lock Nut -2 Rounded Side 8 Assembly 6 • Fasten the pad fasteners to the base fasteners. • Lift the canopy. • Attach the toys to the canopy fasteners. IMPORTANT! Assembly is now complete, but Bounce ‘n Play Activity Dome is not ready for use. Please refer to the Use instructions, on this page, beginning with step 2. ® Pad Fastener Toys Canopy Fasteners 9 • Position one end of the metal canopy stay against the upper hole in a frame. • Insert an M5 x 113/16" screw through the hole in the cover. • Fit the end of the screw through the hole in the metal canopy stay and into the upper hole in the frame. • Push on the cover to insert and “snap” the tab on the cover into the slot in the frame. Make sure you hear a “snap”. • Fit an M5 lock nut (with the rounded side toward the fabric) into the upper hexagonal opening on the back of the frame. • Tighten the screw with a Phillips screwdriver. Do not over-tighten. • Repeat this procedure to attach the other end of the metal canopy stay and the remaining cover to the frame on the other side of the base. Upper Hole Cover Slot Tab Metal Canopy Stay M5 x 113/16" Screw -2 M5 Lock Nut -2 Rounded Side 8 Use 7 • Push down on the product to be sure each side of the base wire is in the correct position.The base wire...