Évaluations - 3, GPA: 4.7
(
)
)
|
Facilité d'utilisation
4055 I Ages 8 + Wow/Wee Contents Introduction p2 Package contents Quick overview p3 Battery details p4 Properly handling FlyTech Bladestar p5 Attaching the blades p5 Charging FlyTech Bladestar p6 Flying locations p7 Operating FlyTech Bladestar p8 Flight modes p9 About Autopilot Mode Tips and tricks for Autopilot Mode p 10 1 Dogfight FlyTech Bladestar! p11 Flight school pi 2 Hovering Direction control Replacing the propellers pi3 Storage pi 3 Troubleshooting guide p14 Tips and tricks pi7 Limited warranty pi8 Thank you for purchasing FlyTech Bladestar™ from WowWee®! FlyTech Bladestar™ is an Al masterpiece only from WowWee®! Changing helicopter flight as we know it, FlyTech Bladestar has exclusive Autopilot Mode with sensor-based navigation. Watch it glide itself through the air avoiding ceilings and flying away from obstacles, or take full control using the 3 channel digital IR controller. Face-off two FlyTech Bladestars - attach the Dogfight accessory to the controller, and press the Fire button to take down your opponent, when in range! Made from light “high-flex" materials and designed to be crash-resistant, FlyTech Bladestar is built for indoor use. Charge FlyTech Bladestar by connecting it to the controller using the built-in charger cable, then take this revolutionary indoor flying machine to the skies! Take a few minutes to look through this user manual to get your FlyTech Bladestar up and flying! NOTE: When using FlyTech Bladestar, adult supervision is required, especially when changing batteries. IMPORTANT: Do not use outdoors. Introduction / Package contents Package Contents • 1 x FlyTech Bladestar • 1 x Controller • 1 x Dogfight accessory • 4x Blades • 2 x Spare propellers Quick overview Quick overview FlyTech Bladestar 3 Controller Battery details The FlyTech Bladestar controller requires 6 x “AA" size alkaline batteries (not included). Install the batteries as follows: 1. Open the battery compartment on the controller using a Phillips screwdriver (not included) to remove the screw on the battery compartment cover. 2. Insert the batteries according to the diagram. Ensure that the positive and negative polarities match the illustrations inside the battery compartment. 3. Replace the battery compartment cover and replace the screw using the screwdriver. Do not over-tighten. Battery details IMPORTANT SAFETY PRECAUTIONS * Never fly FlyTech Bladestar outdoors. * Keep FlyTech Bladestar away from faces and eyes. * Do not launch at people or animals. * Use the charger included in this package to recharge the battery in FlyTech Bladestar. * Keep fingers away from FlyTech Bladestar's moving propellers when in use. * Make sure people around you are aware you are playing with FlyTech Bladestar. * Do not fly FlyTech Bladestar near overhead cables, trees, buildings or any other obstructions. * Always turn OFF when not in use. Attention: Important Battery Information * Use only fresh batteries of the required size and recommended type * Do not mix old and new batteries, different types of batteries [standard (Carbon-ZInc), Alkaline or rechargeable] or rechargeable batteries of different capacities * Rechargeable batteries are only to be charged under adult supervision * Please respect the correct polarity, (+) and (-) * Do not try to recharge non-rechargeable batteries * Do not throw batteries Into the fire * Replace all batteries of the same type/brand at the same time * The supply terminals are not to be short-circuited * Remove exhausted batteries from the toy * Batteries should be replaced by adults * Remove batteries If the toy Is not going to be played with for some time * Rechargeable batteries are to be removed from the controller before being charged * This user manual should be kept because It contains important information Properly handling FlyTech Bladestar / Attaching the blades Properly handling FlyTech Bladestar To avoid unnecessary damage, only hold FlyTech Bladestar by the core. Attaching the blades Before flying FlyTech Bladestar for the first time, or if you have a broken blade, you will need to attach the new blades. You can also replace the original blades on your FlyTech Bladestar if they become damaged or you want it to have a different look.Two spare blades are included in the FlyTech Bladestar package. To attach the blades follow the instructions below: 1. Make sure the controller and FlyTech Bladestar are turned OFF. 2. There are two separate blades on FlyTech Bladestar. Gently remove the old blade(s), if any, by pressing the button located on the clip attached to FlyTech Bladestar's core, and pull the blade gently away. NOTE: Ifyou have difficulty removingthe blade, press the button on the clip with a pen or other thin object IMPORTANT: Do not pull the blade. 3. Install the new blade, the lettering printed on the blade should be on the under side, by pushing it gently into the clip until it clicks into p...