Évaluations - 5, GPA: 4
(
)
)
|
Facilité d'utilisation
• Place the cap nut assembly tool under the assembled rear wheel and onto the cap nut. • Slide a rear wheel (indented side up) onto the end of the straight axle. • Slide a hubcap (peg side down) onto the straight axle. • Place a cap nut on the end of the straight axle. Tap the cap nut with a hammer. Gently pull the rear wheel up to be sure the cap nut is securely attached to the straight axle. • Insert one of the tabs on a cover into a slot in the hubcap. Push to snap the cover into place. Repeat this procedure to attach the other cover to the other hubcap. • Fit two pedal hubs onto the pedal axle tabs. Make sure the tabs fit into the slot in each pedal hub. Pedal Hub Pedal Hub Pedal Axle Tab Tab Slot 4 3 Assembly Hole Pedal Axle Pedal Hubs Front Wheel 5 • While holding the pedal hubs on the pedal axle, insert the pedal axle through the hole in the center of the front wheel. • Push the pedal hubs into the center of the front wheel until they are flush with the surface of the front wheel. Pedal Hub Pedal Hub • Turn the front wheel assembly over. 6 • Insert the remaining pedal hubs on top of and below the pedal axle and into the hole in the center of the front wheel. • Push the pedal hubs into the center of the front wheel until they are flush with the surface of the front wheel. • Fit the pedal on the pedal axle. Tap the pedal with a hammer until it is secure. • Pull the pedal up to be sure it is secure. If you can remove it, you have not secured it properly. Tap it with the hammer again. Pedal Axle Scrap Block of Wood Pedal 7 Fork Arms Pedal Axle Groove Fork Cover 8 • Place the front wheel assembly between the fork arms. Make sure the pedal axle fits into the groove at the bottom of each fork arm. • Place a fork cover over the pedal axle on one fork arm. • Insert two #8 x 3/4" screws into the fork cover and tighten. • Repeat this procedure to attach the other fork cover to the other fork arm. 4 • Insert the fork post up through the hole in the neck of the frame. Make sure the fork is positioned so that the fork covers face the rear wheels. • Place the handlebar onto the fork post and push it down onto the frame. Make sure the handlebar is positioned so that the screw hole faces the rear wheels and aligns with the screw hole in the fork post. Hint: You may need to rotate the handlebar to align the holes. • Insert the #8 x 3" screw through the hole in the handlebar and into the fork post so that part of the screw (about 3/4") is still visible. Tighten the screw. Handlebar Frame Neck Fork Post Fork Cover Rear of Trike • Position the seat upside down. • Fit the small pegs on the seat retainer into the holes in the seat. • Insert and “snap” the cap into the hole in the frame. Cap Seat Retainer Seat Peg Holes 9 10 12 11 • Fit the tab on the headlight cover to the slot in the top of the handlebar. • Insert two #6 x 1/2" screws into the headlight cover. Tighten the screws. Headlight Cover Slot Assembly 5 • At an angle, insert the tabs on the seat into any of the top three sets of slots for the lower, middle or upper position. • Lower the seat so that the seat retainer inserts and snaps into the slots in the frame. • Pull up on the seat to be sure it is secure. Seat Hint: The seat can be attached to the frame in any of three positions, depending on the size of your child. Check your child’s fit on the trike by observing the seat to pedal distance, as it is being ridden. If the pedals seem too far away or too close for your child, move the seat up or down. • Make sure the areas where the labels will be applied are clean and dry. Wipe your vehicle with a clean, soft, dry cloth to remove any dust or oils. • For best results, avoid applying a label more than once. • Apply the labels as shown in the illustration above. • After applying the label, rub the label firmly with a cloth to make sure the label is adhered to your vehicle. Lower Position Middle Position Upper Position Tabs Slots Seat Retainer 10 (Place label 9 on opposite side of seat) (Place remaining label 1’s on opposite side of front wheel) 5 (Place label 11 on opposite side) (Place label 4 on opposite side) 2 6 14 SIDE VIEW DASH VIEW 13 3 (Place label 8 on opposite side) 7 12 Label Decoration Attaching the Seat 6 Battery Replacement Battery Safety Information For best performance, we recommend replacing the batteries that came with this trike with three, new alkaline "AA" (LR6) batteries. Headlight Cover 1 • Loosen and remove the two screws from the headlight cover. Remove the headlight cover. 2 1.5V x 3 “AA” (LR6) Hint: When sound or lights become faint or stop, it's time for an adult to replace the batteries. We recommend the use of alkaline batteries for longer battery life. Battery Compartment • Loosen the screw in the battery compartment door. Open the battery compartment door. • Insert three "AA" (LR6) alkaline batteries. • Close the battery compartment door and tighten the screw. • Replace the headlight cover. Replace the screws and tighten. • If this ...