Évaluations - 5, GPA: 4
(
)
)
|
Facilité d'utilisation
or BSI approved type. • Refit the fuse cover. If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate plug fitted in its place. If the mains plug contains a fuse, this should have a value of 5A. If a plug without a fuse is used, the fuse at the distribution board should not be greater than 5A. HOW TO CONNECT A PLUG The wires in the mains lead are coloured in accor dance with the following code: BLUE – “NEUTRAL” (“N”) and BROWN – “LIVE” (“L”). As these colours may not corre- spond with the colour markings identifying the terminals in your plug, proceed as follows: • The BLUE wire must be connected to the ter- minal which is marked with the letter “N” or coloured BLACK. • The BROWN wire must be connected to the terminal which is marked with the letter “L” or coloured RED. • Do notconnect either wires to the earth ter- minal in the plug which is marked by the let- ter “E” or by the safety earth symbol or coloured green or green-and-yellow. Before replacing the plug cover, make certain that the cordgrip is clamped over the sheath of the lead – not simply over the two wires. NOTE The severed plug must be disposed to avoid a possible shock hazard should it be inserted into a 13A socket elswhere. Installation Cassette SUPPLY Battery supply (See 2) • Open the battery compartment and insert as indicated 4 batteries, type R20, UM1 or D-cells. • Remove the batteries if exhausted or if they will not be used again for a long period. • The battery supply is switched off when the set is connected to the mains. To change over to battery supply, pull out the plug from the MAINS socket. Mains supply (See 3) • Check if the mains voltage as shown on the model number plate (on the base of the set) corresponds to your local mains voltage. If it does not, consult your dealer or service organisation. • Connect the mains lead to the MAINS socket and the wall socket. The mains supply is switched on. To disconnect the set from the mains completely, withdraw the mains plug from the wall socket. The model number and production number are located on the base of the set. This product complies with the radio interference requirements of the European Community. CASSETTE RECORDER Copyright Recording is permissible insofar as copyright or other rights of third parties are not infringed. Fast winding and rewinding Press fast forward wind F.FWD 5 or REWIND 6 button. To stop, press STOP 9. Safeguarding a cassette against erasure Keep the cassette side to be safeguarded in front of you and break out the left tab. Now, recording on this side is no longer possible. CASSETTE PLAYBACK • Set the TAPE/RADIO selector to TAPE. • Press EJECT 9 and insert a cassette. – For playback, any cassette type can be inserted. • To start playback, press PLAY (. • Adjust the sound with the controls VOLUME and DBB. – You may connect stereo headphones with 3.5 mm plug to socket p. The loudspeaker is then muted. • To stop, press STOP 9. The set is then switched off. On pressing again, the cassette holder will open (EJECT). When the end of the tape is reached, the recorder buttons are released. RECORDING • Press EJECT 9 to open the cassette holder. • Insert the cassette. • For recording you must use a NORMAL cassette (IEC I) on which the tabs are not removed. – At the very beginning of the tape, no recording will take place during the first 7 seconds when the leader tape passes the recorder heads. • When monitoring during recording, adjust the sound with the controls VOLUME and DBB. These controls do not affect the recording. Recording from the radio • Set the TAPE/RADIO selector to RADIO. Starting and stopping the recording • To start recording, press RECORD 0; in doing so, PLAY ( is pressed too. • For brief interruptions, press PAUSE ;. Press again to restart recording. • To stop, press STOP 9. On pressing again, the cassette holder will open (EJECT). – When the end of the tape is reached, the recorder buttons are released. • The set is switched off if TAPE/RADIO selector is in position TAPE and the recorder buttons are released. 1 Radio/Maintenance Troubleshooting RADIO RECEPTION • Set the TAPE/RADIO selector to RADIO. • Adjust the sound with the controls VOLUME and DBB. – You may connect stereo headphones with 3.5 mm plug to socket p. The loudspeaker is then muted. • Select the wave band using BAND selector. • Tune to a radio station using TUNING knob. (LW not on all versions). – For FM, pull out the telescopic aerial. To improve FM-reception, incline and turn the aerial. Reduce its length if the FM-signal is too strong (very close to a transmitter). – For AM/MW and LW (Medium and Long Wave), the set is provided with a built-in aerial, so there is no need to use the telescopic aerial. The aerial can be directed by turning the whole set. • The set is switched off if the TAPE/RADIO selector is in position TAPE and the recorder buttons are released. MAINTENANCE (see 4) Clean the parts indicated after every 50 hours of operati...
Ce manuel est également adapté pour les modèles :Montres - AQ4050/17 (249.87 kb)