Évaluations - 3, GPA: 3.7
(
)
)
|
Photos et spécifications Sony ICD-P330F |
Par ce dispositif a également d'autres instructions :
Facilité d'utilisation
• If you try to set the alarm to play back a message at a previously set time on another message, “PRE SET” will be displayed, preventing new settings. • If the alarm time comes while another message is being played back with an alarm, the playback stops and the new message will be played back. • If the alarm time comes during recording, alarm will sound for 10 seconds after the recording is finished and playback begins. “,” will flash when the alarm time comes. • If more than one alarm time comes during recording, only the first message will be played back. • When the alarm time comes when the unit is in the menu mode, alarm will sound and the menu mode will be canceled. • If you erase the message you set the alarm to play back, the alarm setting will be canceled. • If you divide a message with the playback alarm, playback will stop at the point you divided a message. • You can adjust the playback volume with the VOL control. • If the alarm time comes during erasing, alarm will sound for 10 seconds after the erasing is finished and playback begins. • Alarm setting will not be canceled when the alarm playback finishes. To cancel alarm setting, see below. To cancel or change the alarm setting 1 Select the message you set the alarm to play back, and press DISPLAY/MENU for more than 1 second to enter the menu mode. 2 Press – . or > + to select “ALARM ON”. 3 Press NxPLAY/STOP to flash “ON”. 4 To cancel the alarm setting: Press – . or > + to flash “OFF” and press NxPLAY/STOP. To change the alarm setting: Press NxPLAY/STOP. When the alarm date is displayed, follow the Steps 3 to 6 of “Playing Back a Message at a Desired Time with an Alarm” to change the alarm setting. 5 Press xSTOP to exit the menu mode. Preventing Accidental Operation — HOLD function Slide the HOLD switch to “ON”. “HOLD” will flash three times, indicating that all the functions of the buttons are locked. When the HOLD function is activated during stop, all the display will be turned off after “HOLD” flashes. HOLD To cancel the HOLD function Slide the HOLD switch to “OFF” . Note When the HOLD function is activated during recording, cancel the HOLD function first to stop recording. 1 Tip Even if the HOLD function is activated, you can stop the alarm playback. To stop the alarm or playback, press xSTOP. Selecting the Display Mode You can select the display mode for the stop, recording and playback modes. Each time you press DISPLAY/MENU, the display mode will change as shown below: 1 On the current time display If the unit is left unoperated for more than 3 seconds in the stop mode, the display will show the current time, regardless of the display mode setting. Counter: B Elapsed playback/recording time in one message m Remaining time (REMAIN): In the playback mode: The remaining time of one message indication. In the stop and recording mode: The remaining recording time indication. m Recorded date (REC DATE)*: The date the current message was recorded. m Recorded time (REC DATE)**: The time the current message was recorded. * If the clock has not been set, “--Y--M--D” will be displayed. **If the clock has not been set, “--:--” will be displayed. Playing Back a Message at a Desired Time with an Alarm You can sound an alarm and start playback of a selected message at a desired time. If you select “B-ONLY” in Step 6, an alarm sounds only and playback will not start. 1 Select the folder (See “Selecting the Folder” on the front side) and display the message you want to play back with an alarm. 2 Enter the alarm setting mode. 1 Press DISPLAY/MENU for more than 1 second until “MODE” appears in the display window. 2 Press – . or >+ to select “ALARM OFF” (If the alarm has already set to the selected message, “ALARM ON” is displayed. If you do not wish to change the setting, press xSTOP and exit the menu mode.) Note “ALARM OFF (or ON)” will not appear and the alarm cannot be set if the clock has not been set or no message has been recorded in the selected folder. 3 Press NxPLAY/STOP. “OFF” starts to flash. 4 Press – . or >+ to select “ON”. “ON” starts to flash. 5 Press NxPLAY/STOP. “DATE” will flash in the display window. 3 Set the alarm date. To play back on a desired date (the message will be played back at the same time on the same date every year until you erase the message) 1 Press NxPLAY/STOP while “DATE” is flashing. The year digits will flash. 2 Press – . or > + to select the year digits and press NxPLAY/STOP. The month digits will flash. 3 Press – . or >+ to select the month digits and press NxPLAY/STOP. The day digits will flash. 4 Press – . or >+ to select the day digits. To play back once a week Press – . or >+ to select the day of the week. To play back at the same time every day Press – . or >+ to select “DAILY”. 4 Press NxPLAY/STOP. The hour digits will flash. 5 Set the alarm time. 1 Press – . or >+ to select the hour digits and press NxPLAY/STOP. The minute digits will flash. 2 Press – . or >+ to select the minute digits and press NxPLAY/STO...