Évaluations - 6, GPA: 3.5
(
)
)
|
Facilité d'utilisation
American Sankey Keg Coupler 2. Faucet 11. Metal Keg Floor Support 3. Beer Tower 12. Caster Washer (x2) 4. Guard Rail 13. Casters (x4) 5. Drip Tray 14. Neoprene Washer 6. Regulator 15. Snap-On Clamps (x2) 7. CO2 Tube 16. Wire Shelves (not shown) (x2) 8. CO2 Cylinder (supplied empty) 17. Half Barrel Keg (not included) 9. Cylinder Holder 18. Faucet Wrench Thank you for purchasing the EdgeStar Beer Dispenser. Are you ready to enjoy some draft beer now? All you need is: • Included components (pictured to the left) • Wrench • Flat head screwdriver • Pair of pliers/clamp crimper • Full keg of beer (1/2 barrel size or smaller [pictured to the left but not included]) Note: Any Coors Brand or Miller Rubber Sided kegs will not fit inside this unit. • Also, fill the included CO2 tank with CO2 (Most beer keg providers can fill your CO2 tank) Notice: this manual is provided as a supplement to the owner’s manual. Please refer to the owner’s manual for a full discourse on installation, usage and maintenance. Note: Parts listed throughout this installation guide are numbered according to the diagram parts list. Install Caster Wheels Make sure unit is empty (including white metal keg floor(11)). Carefully tip the beer dispenser on its side. Connect the casters(13) to the cabinet by screwing in each metal bracket into one of four caster holes (casters in the front of the cabinet require the washers(12)). Then carefully set the unit upright Note: allow dispenser to stand in an upright position for 8 hours before turning on the power. Remove Plug Open the door, and with your hand push the top cabinet plug through the top of the cabinet. Use flat head screwdriver as a prying tool if necessary. Install Tower Now begin installing the tower(3). Unravel the beer line hose from the bottom of the tower, and feed the hex nut and beer line through the hole you uncovered in the top of the cabinet. Secure Tower Once you have fed all the line into the cabinet, you can now place the tower into the unit. Align the black plastic adapter on the bottom of the tower to the hole in the top of the cabinet. The adapter should mate securely with the hole. Then turn the adapter about 25° to lock it into place. The faucet connection for the tower should now face the front of the cabinet. If the tower is not facing the front of the cabinet, remove it and reinstall it from another position. 4Install Railing Take the railing(4) and slide its “feet” into the pilot holes in the top of the cabinet Warning: This guide is provided for informational purposes only. If you have any questions about Warning: CO2 can be dangerous! CO2 cylinders contain high-pressure gas, which can be hazardous if the installation of this appliance, feel free to contact EdgeStar service at 866.319.5473 or consult handled improperly. Please handle with care. a qualified installer. Neither the manufacturer nor its distributors shall be liable for any incidental, consequential, indirect, special, or punitive damages of any nature, including without limitation, Note: Included accessories may not be as pictured lost revenues or profits, or any other damage whether based in contract, tort, or otherwise. Installation Guide Beer Dispenser 866-319-5473 For assistance, please call: Installation Guide Beer Dispenser 866-319-5473 For assistance, please call: 5 6 7 Install Handle & Faucet Screw the black faucet handle(1) onto the faucet (2). Line up the metal “teeth” on the faucet with the metal “teeth” of the faucet adapter on the front of the tower(3). Make sure the faucet is vertical with the black handle facing the ceiling. The faucet should then be first “hand tightened,” then secured with the faucet wrench(18). Now place the plastic drip tray(5) beneath the faucet. Connect Tube to Regulator Make sure the CO2 regulator(6) shut off valve is closed- the switch below the main body should be perpendicular to the tubing. Install the 4 ft. CO2 gas line tube(7) to the regulator by attaching one end of the tube into the hose barb connection on the CO2 regulator. Secure the tube by using one of the two self-locking red plastic snap-on clamps(15). Use pliers or clamp crimpers to snap the clamp on as high as possible. Make sure the clamp does not impeed the valve. Then remove the black rubber plug from the back of the unit and feed the remaining unused end of the tubing through the hole. Connect Regulator to Cylinder Make sure the CO2 cylinder(8) is full and closed. Then attach the CO2 regulator(6) to the CO2 cylinder by screwing the loose golden regulator nut into the cylinder valve and tightening with a wrench or pliers. Note that a fiber washer is normally required to connect a regulator to a CO2 cylinder, but the standard regulator provided includes a built-in o-ring. 8Mount CO2 Cylinder Now mount the CO2 cylinder holder(9) to the cabinet. Match up the holes on the holder with the four screws jutting out of the back of the cabinet and slide the holder down to lock it in place. Position the CO2 reg...