Évaluations - 4, GPA: 4.3
(
)
)
|
Facilité d'utilisation
. When Mux Fwd is disabled, the DSLAM forwards traffic based on a destination MAC address. Either enabled or disabled, traffic is forwarded on ports having the same VLAN designation. IP Filter – Enable/Disable (Default = Disable). There must be an entry in this field. . When IP filtering is enabled, the DSLAM looks at IP traffic from the subscriber to authenticate the source IP address. . When IP filtering is disabled, traffic passes all protocols. This does not apply to packets that are not IP type. IP Scoping – Enable/Disable (Default = Enable). There must be an entry in this field. . When IP Scoping is enabled, the DSLAM intercepts IP ARP and DHCP requests and responses. . When IP Scoping is disabled, the DSLAM allows non-IP traffic to be forwarded. Domain Name – Enter the domain name of the Internet Service Provider (ISP). Port VLAN (Port) A-E-C Gives the user the ability to configure one VLAN association on an individual port. DSL Port # – Enter the DSL port number (Default = 1). VLAN – Number of the VLAN port (Default = none). This field is read-only. Default NHR – Enter the IP address of the next hop router in nnn.nnn.nnn.nnnformat (Default = none). If the NHR IP address does not exist for that port, a default NHR IP address is used. If the default NHR IP address does not exist, the Address Resolution Protocol (ARP) request is ignored. May 1998 8000-A2-GB26-00 8310 MVL and 8510 DSL Card Configuration 8310 MVL and 8510 DSL Card Configuration Client VLAN (Client) A-E-D Gives the user the ability to configure static clients on VLANs. As there are up to 32 clients per port, multiple screens are required to completely configure the port. For a list of VLAN IDs, press Ctrl-v. DSL Port # – Enter the DSL port number (Default = 1). Number of clients – Enter the number of clients to configure (0 – 32) (Default = none). User – Enter the input number of the client (0 – 32) (Default = 0). IP Address – Enter the client IP address in nnn.nnn.nnn.nnnformat (Default = none). There must be an entry in this field. Typically, all IP addresses in the same VLAN would be on the same subnet. NHR – Enter the IP address of the default next-hop router in nnn.nnn.nnn.nnnformat (Default = none). VLAN – VLAN ID between 2 and 4094. (This field is read-only.) Type – S = Static or D = Dynamic. (This field is read-only.) ARP (Parameters and Add ARP Entry) A-E-E (A and B) Select: Parameters (A) Gives the user the ability to configure general Address Resolution Protocol (ARP) cache parameters. Complete Entry Timeout (minutes) – Length of time that a complete entry remains in the ARP Table before removal. A complete entry is one for which there is a MAC address and a node has responded to the ARP request. Range = 1 to 200,000 minutes. (Default = 20) Incomplete Entry Timeout (minutes) – Length of time in minutes that an incomplete entry remains in the ARP table before being removed. (An incomplete entry is an entry without a MAC address.) This is also the amount of time that a packet will remain in the system while waiting for address resolution. Range = 1 to 255 minutes. (Default = 3) NOTE: If you have made changes to this screen, you must do a card reset. ARP Entry (Add ARP Entry) (B) Gives the user the ability to add entries into the ARP cache. Item – Enter 0 (zero) to add a new record. IP Address – nnn.nnn.nnn.nnnformat. MAC Address – xx-xx-xx-xx-xx-xxformat. VLAN – Enter a VLAN ID between two and 4094 (Default = Null). There must be an entry made in this field. Trailer – Yes/No (Default = No). Perm – Yes/No (Default = No). If you select yes for Perm and no to proxy, the ARP entry will be saved in NVRAM (up to 32 entries). These are loaded when the card reboots. NOTE: For the Add ARP Entry screen, all other information entered is not stored in the nonvolatile memory and will be lost when you reset the card. 8000-A2-GB26-00 May 1998 8310 MVL and 8510 DSL Card Configuration 8310 MVL and 8510 DSL Card Configuration Use the SN Configuration screen to configure endpoint Service Node information. . Procedure 1. Follow this menu sequence: Configuration"SN Configuration(A-F). 2. The SN Configuration menu appears. Enter the desired value on the selected screen and field as shown in Table 5-5 and press Return. Table 5-5. Service Node Options SN Configuration A-F Displays endpoint information for the 5620 DSL or 6310 MVL Service Node. Port # – Enter the DSL or MVL port number (1 to 4). SN Type – Model number of SN connected to the DSL port. For Model 8510, the SN is 5620. For Model 8310, the SN is 6310. (This field is read-only.) System Name – 16 alphanumeric characters. Enter the name assigned to the SN. System Contact – 32 alphanumeric characters. Enter the name or number of the person responsible for the SN. System Location – 16 alphanumeric characters. Enter the location of the SN. Model Num – Model number of card. (This field is read-only.) Serial Num – Serial number of card. (This field is read-only.) Firmware Rev – Version of firmware. (...
Ce manuel est également adapté pour les modèles :Dispensers - HOTWIRE 8310 MVL (502.78 kb)