Évaluations - , GPA:
(
)
)
Fabricant : Bunn
Taille : 368.24 kb
Nom Fichier : 29793.0001.pdf
Langue d'enseignement: 
Le document est chargé, s'il vous plaît patienter
 |
Le document est chargé, s'il vous plaît patienter
Facilité d'utilisation
10. Place level probes in notch in rim of hoppers and install hoppers. 10. Install PAF units onto hoppers and platform. 11. Plug PAF power cord into rear of platform. 12. Plug PAF platform power cord into proper electrical outlet. 13. Attach a flexible water line to the .25” flare fitting on the back panel of the Powder Auto-Fill. NOTE: A water strainer assembly (BUNN-O-MATIC #23820.1000) should be installed in line prior to the flexible water line. NOTE - Water pipe connections and fixtures directly connected to a potable water supply shall be sized, installed and maintained in accordance with federal, state and local codes. USER NOTICES Carefully read and follow all notices on the equipment and in this manual. They were written for your protection. All notices are to be kept in good condition. Replace any unreadable or damaged labels. As directed in the International Plumbing Code of the International Code Council and the Food Code Manual of the Food and Drug Administration (FDA), this equipment must be installed with adequate backflow prevention to comply with federal, state and local codes. For models installed outside the U.S.A., you must comply with the applicable Plumb- ing /Sanitation Code for your area. Artwork for P/N: 00656.0001Artwork Rev: ADrawn: REFDate: 04/22/10 00824.0002 00656.0001 Push back until fully latchedbefore removing or manuallyfilling chilled product hopper. 00986.0000 34561.0000 37881.0000 29793.1 081511 OPERATING INSTRUCTIONS 1. On the Ultra touch pad, make the following settings: a) POWER- “ON” b) DAY/NIGHT- “DAY” 2. Pull the Powder Auto-Fill fully forward on its support rails and open the door. 3. Fill the Powder Auto-Fill product hopper as follows: a) Pull the slide gate closed on the Powder Auto-Fill product hopper elbow and remove the hopper from the Powder Auto-Fill. b) Remove the lid from the product hopper and fill the hopper with a powdered granita mix. c) Install the product hopper into the Powder Auto- Fill. Insure hopper is fully seated behind retainer plates. d) Push the slide gate on the hopper ejector elbow to the open position. 4. Place the ON/OFF switch at the Powder Auto-Fill whipper panel to “ON”. 5. After allowing 5 seconds for the Powder Auto-Fill to initialize, observe the door lamp. The door lamp should not be lit. If the door lamp is lit, consult the fault list located on the decal placed on the back of the door. Clear the fault before proceeding. NOTE: If the Powder Auto-Fill is being used for the first time with the selected granita mix, perform an adjustment as described in ADJUSTMENTS. 6. Close the Powder Auto-Fill door and observe the following: a) The door lamp lights steadily. b) The Powder Auto-Fill begins dispensing liquid granita product. 7. The Powder Auto-Fill will continue to fill the ULTRA product hopper until the liquid level in the ULTRA hopper reaches the product level probe or for 5 minutes, which ever occurs first. 8. If the Powder Auto-Fill fails to fill the ULTRA hopper in 5 minutes, the following will occur: a) The Powder Auto-Fill will stop dispensing product. b) The door lamp will flash 4 times about every 2 seconds. 9. After checking the ULTRA and Powder Auto-Fill set-up, the 5 minute refill fault may be cleared by simply opening and closing the Powder Auto-Fill door. 10. Once the product level in the ULTRA covers the auger, make the following switch settings at the ULTRA control panel: a) AUGER - “1”. b) ICE/OFF/CHILL - “ICE” or “CHILL” as appropriate for the granita product. 11. From this point onward, the Powder Auto-Fill will continue to automatically refill the ULTRA hopper, maintaining the ULTRA product at an approximate 2 gallon level. 12. When the Powder Auto-Fill powder level falls low, the door lamp will cycle ON and OFF, but will continue to dispense product for a preset period. When this period expires, the Powder Auto-Fill will continue to cycle the door lamp ON and OFF and will stop dispensing product. 13. To clear the low product fault, simply refill the powder as follows: a) Open the Powder Auto-Fill door. b) Close the hopper slide gate. c) Remove the product hopper. d) Refill the product hopper with powdered granita mix. e) Replace the hopper. f) Push the slide gate on the hopper ejector elbow to the OPEN position. g) Close the Powder Auto-Fill door. 29793.1 021202 ADJUSTMENTS When using the Powder Auto-Fill with a new powdered granita mix, follow the procedure outlined below to adjust the Powder Auto-Fill to produce the correct recipe. 1. Determine the mix ratio of powdered granita mix. Convert the recipe so that it is expressed in terms of weight units [grams (g), dry ounces (oz), or pounds (lbs)] of powdered granita mix to fluid ounces (fl. oz.) of water [1 gallon (gal) = 128 fl.oz.; 1 liter (l) = 33.8 fl.oz.]. 2. The delivery rate of the water ingredient is factory preset to 1 fl.oz. per second. Therefore, it is only necessary to adjust the delivery rate of the powdered granita mix. Adjustment is accomplished ...