Évaluations - 2, GPA: 4.5
(
)
)
|
Facilité d'utilisation
2. Inspect and remove any remaining packaging, tape or printed materials before turning on the beer dispenser. Note: Allow the beer dispenser to stand in an upright position for 2 hours before turning on the power. Check all supplied accessories in the carton to be sure that all pieces are present and in good condition. A checklist of accessories is listed below for your reference. If you find any accessories that are not in good condition or are missing, please contact our customer service department for assistance. Our Toll-Free number is 1-877-337-3639. 1 Beer Tap Including: 1 Gasket for the Beer Tap 1 Washer for Connection to the Keg Coupler 1 CO2 Regulator 1 CO2 Cylinder 1 Keg Coupler 1 Cleaning Kit 1 CO2 Air Line 2 Hose Clamps 1 CO2 Cylinder Retainer 1 Guardrail 1 Drip Tray 4 Casters 1 Wrench 4 Large Phillips-Head Screws 8 Small Phillips-Head Screws 2 Retainer Fixing Screws 2 Wire Shelves 4 Support Pins English Parts and Features 12 3 4 5 6 7 8 9 10 1. Front Casters 7. Chrome Beer Tap 2. Interior Keg Floor Support 8. Adjustable Thermostat (Located in rear.) 3. Cabinet 9. Drip Tray 4. CO2 Tank 10. Keg (Not included. Shown for 5. Worktop illustration purposes only.) 6. Chrome Guardrail English Proper Location • To ensure that your beer dispenser works at the maximum efficiency it was designed for, install it in a location where there is proper air circulation, plumbing and electrical connections. • Choose a location where the beer dispenser will be away from heat and will not be exposed to direct sunlight. • This beer dispenser is designed for indoor use only and should not be used outdoors. • This beer dispenser is a freestanding design and should not be placed in a built-in or recessed area. • The following dimensions are the recommended clearances around the beer dispenser. Sides........................3/4" (19mm) Top ..............................1" (25mm) Back ............................1" (25mm) English Assembly Instructions Read carefully and understand all installation instructions before installing the beer dispenser. If after completing the process you are still unsure whether the beer dispenser has been properly installed, we recommend that you contact a qualified installer. Installing the Casters Nut Follow the steps below to install the casters. 1. Empty the inside of the cabinet completely and lay the beer dispenser down sideways. We recommend that you place a piece of cardboard or cloth underneath the cabinet to prevent dents or scratches to the cabinet. 2. Insert the casters into the holes on the bottom corners of the cabinet. Tighten each caster by turning the nut clockwise with the wrench provided. 3. Once all four casters have been tightened evenly, stand the cabinet in an upright position. Installing the Beer Tap Follow the steps below to install the beer tap. 1. First, remove the cabinet plug located on the Handle worktop. Firmly grasp the cabinet plug, twist and pull upward. Note: Store this plug in a safe place as it will be required when converting the beer dispenser into a refrigerator. 2. Place the gasket over the wing nut on the bottom of the beer tap. 3. Pass the beer tube through the gasket to the base of the beer tap. 4. Push both the wing nut and the beer duct through the hole in the worktop until the beer tap is resting on top of the cabinet. 5. Align the holes of the beer tap with the gasket and pilot holes on the worktop of cabinet. 6. Secure the beer tap to the cabinet by inserting four large Phillips-Head screws into the holes and tightening. Wrench Caster Large Philip Head Small Phillips Head Draft Arm Assembly Gasket Beer duct Guard Rail wing nut pilot holes English Installing the Guardrail Follow the steps below to install the guardrail on the worktop. 1. Place the guardrail on top of the cabinet. 2. Align all holes of the guardrail with the holes of the cabinet. 3. Secure the guardrail to the cabinet with eight small Phillips-Head screws. Installing the CO2 Regulator and CO2 Cylinder Follow the steps below to safely install the CO2 regulator and CO2 cylinder. You must read and understand the following procedures for CO2 cylinders before installation. Note: Your CO2 cylinder is shipped empty to avoid any possible accidents during transportation. When you purchase the first keg of beer, have your beer distributor fill the CO2 cylinder. 1. Install the CO2 air line hose to the regulator by attaching one end of the red air line hose to the hose barb connection on the CO2 regulator. Secure the hose by using one of the two self-locking black plastic snap-on clamps. Use pliers to snap the clamp on tightly to ensure that there are no leaks. 2. Attach the CO2 regulator to the CO2 cylinder by screwing the regulator nut onto the cylinder valve and tightening with an adjustable wrench. 3. Remove the nut from the retainer bolt. Use two retainer fixing screws to secure the retainer to the holes on the back of the cylinder. 4. Slide the cylinder through the retainer and place it...