Do not use where water is microbiologically unsafe or with water of unknown quality. If bacterial contamination is present, a recognized method of water disinfection is required. Check with your public works department for applicable local plumbing and sanitation codes. Follow your local codes if they differ from the standards used in this manual. Operational, maintenance and replacement requirements are essential for this product to perform properly. The Culligan Water Tower contains replaceabl

The display will blink “SLtP” if set to English or “SLtG” if set to Metric for 3 seconds and then display the salt dosage. Adjust the setting with the “+” or “-” key (3-24 lbs.) (1-10 kgs.) Note: This option will not show if the control is set to Filter mode. Step 4 – Programming Backwash Time Press the “Status” key after programming salt dosage. The display will blink “bw” for 3 seconds and then display the backwash time in minutes. Adjust the setting with “+” or “-” key. (1-40 minutes) Program

• The contaminants or other substances removed or reduced by the selected cartridge are not necessarily in your water. Ask your local water municipality for a copy of their water analysis, or have your private well tested by a reputable water testing lab. • After prolonged periods of non-use (such as during a vacation) it is recommended that the system be flushed thoroughly. Let water run for 5–6 minutes before using. • The filter cartridge used with this system has a limited service life. Chang

Test Water Feed Product Hardness Iron Hydrogen Sulfide Chlorine TDS Other Comments: Bypass Valve Bypass in Service or Bypass? Condition of bypass valve Operation OK? Control Valve Condition of Eductor (Sulfur-Cleer™) Condition of Solution Valve (Sulfur-Cleer™) Condition of Seal Pack and Brine Piston Condition of Solenoid Valve Condition of Motor: Condition of Flow Control Condition of Switches: Condition of Check Valve Condition of Compressor Output PSI Control settings Before After Check / rese

01881923 Rev. D 01/06/03 DCO# 5378 Culligan® Preferred™ Series Drinking Water Filters Installation, Operation, and Service Guide SPECIFICATIONS Operating Pressure Range: 10 - 125 psi (0.7 bar - 8.6 bar) Operating Temperature Range: 35 - 100°F (2 - 38°C) Service Flow Rate: 0.5 gpm (1.9 Lpm) Capacity: 750 gal. (2,839L) Preferred 150 1000 gal. (3,785L) Preferred 250 300 gal. (1,135L) Preferred 350 For cold water use only NSF/ANSI 42 NSF/ANSI 53 ANSI ACCREDITED CERTIFICATION PROGRAM NSF's Certificat

Failure to do so may result in cracking of the filter and water leakage. NOTE: Make certain that installation of this system complies with all state and local laws and regulations. FOR COLD WATER USE ONLY. MAINTENANCE: Contact your area retailer for replacement cartridges and pricing or call Culligan Customer Service at 800-634-1455 for the nearest dealer. Change cartridge every 2500 gallons or approximately every 12 months. Filter Installation Instructions (For copper or plastic tubing) NOTE:Sh

If leaks persist, or if there are other leaks on system, turn off water supply. Call Technical Support at 1-800-645-5426. Reparaciones Goteras... Entre el pocillo y la tapa. 1. Cierre el abastecimiento de agua y oprima el boton rojo de aliviar la presion. 2. Limpie y lubrique la arandela redonda y atornille el pocillo de nuevo a la tapa aseguradolo manualmente solamente. NO APRIETE CON EXAGERACION. 3. Cierre el abastecimiento de agua. Si continua goteando, o si tiene otras goteras en el sistema,

(1 month = approximately 4000 gallons). **NOTA: el flujo de agua es medido a 60 psi/4.1 bar +Entre mas pequena la clasificacion de micra, lo mas pequena particulas la cual el filtro filtrara. Con motivo de comparar, el cabello humano es aproximadamente 70 micras. Particulas mas pequenas de 40 micras no son visibles a simple vista. 4 Warranty This warranty applies to the Filter Housing. It does NOT apply to any disposable filter cartridge where life expectancy varies with the water being filtered

For a period of TWO YEARS The control valve internal parts. The brine valve and its component parts. The salt storage container internal components. For a period of FIVE YEARS The control valve body, excluding internal parts. The fiberglass wound container(s), if so equipped*. The salt storage container(s), if so equipped. The epoxy-lined steel conditioner tank(s), if so equipped. For a period of TWELVE YEARS The conditioner tank, if it contains a plastic liner. * The tank must be protected by a

lb 870 1,150 1,750 2,530 3,550 7,000 8,800 10,800 18,500 25,000 kg 390 520 790 1,150 1,610 3,175 4,000 4,900 8,390 11,340 NOTES: 1 Service flow rates are based on 7 gpm/ft2 (26 L/m2/min) for Normal and 15 gpm/ft2 (57 L/m2/min) for Peak Flow rates. Actual service rate can vary from 2 to 20 gpm/ft2 (8 - 76 L/m2/min) depending upon the application and the raw water. 2 Backwash flow rates are based on 12-14 gpm/ft2 (45-53 L/m2/min) using 50° F (10° C) water. A different backwash rate may be required