Évaluations - 3, GPA: 3.7
(
)
)
|
Photos et spécifications Sony HT-SF360 |
Par ce dispositif a également d'autres instructions :
Home cinéma - HT-SF360 (3.33 mb)
Home cinéma - HT-SF360 (1.95 mb)
Facilité d'utilisation
Then, press @. Item Explanation SAVE Saves the measurement results and exits the setting process. WRN CHK Displays warning concerning the measurement results. See “When you select “WRN CHK”” (page 26). DIST Displays the measurement result for speaker distance. LEVEL Displays the measurement result for speaker level. EXIT Exits the setting process without saving the measurement results. Note After “SAVE” is displayed for 50 seconds, the measurement result is saved automatically, without the need to save the procedure. 3 Save the measurement result. Select “SAVE” in step 2. The measurement results are saved. When error codes appear Try the remedies and perform the Auto Calibration again. Error code Cause and remedies ERROR 32 • The sound input from the optimizer microphone is out of the acceptable range. • The optimizer microphone or subwoofer may be damaged. Contact your Sony dealer or local authorized Sony service facility. ERROR F 33 The front speakers are not connected. Check that the front speakers are connected properly. ERROR SR 33 Either the surround left or surround right speaker is not connected. Check that the surround speakers are connected properly. continued 25GB Getting Started Error code Cause and remedies ERROR SW 33 The subwoofer may be damaged. Contact your Sony dealer or local authorized Sony service facility. When you select “WRN CHK” If a warning on the measurement result is present, detailed information is displayed. Press © or B to return to step 2 of “Confirming/saving the measurement results”. Warning code Explanation WARN 40 The Auto Calibration has completed. However, the noise level is high. You may be able to perform the Auto Calibration properly if you try it again, even though the measurement cannot be performed in all environments. Try to perform the Auto Calibration in a quiet environment. WARN 41 The sound input from the WARN 42 optimizer microphone is out of the acceptable range. The distance between the optimizer microphone and the speakers is too closed. Set them away, and then try to perform the Auto Calibration. WARN 43 The distance and position of a subwoofer cannot be detected. This may be caused by noise. Try to perform the Auto Calibration in a quiet environment. NO WARN There is no warning information. When you select “DIST” or “LEVEL” You can check the speaker distance or speaker level. When you have finished Disconnect the optimizer microphone from the receiver. Note If you have changed the position of the speakers, it is recommended that you perform Auto Calibration again in order to enjoy the surround sound. Clearing the measurement result You can delete the result of Auto Calibration. If there is no saved data, you cannot delete the result. 1 Press AMP MENU. 2 Press V/V repeatedly until “A.CAL” appears, then press © or b. 3 Press V/V repeatedly to select “A.CAL CLR”, then press © or b. 4 Press V/V repeatedly to select “YES”, then press ©. The saved result is deleted. The settings for speaker distance and speaker level return to their defaults. 26eß 8: Adjusting the speaker levels (TEST TONE) You can adjust the speaker levels while listening to the test tone from your listening position. 1 Press AMP MENU. “SET HDMI” appears on the display. 2 Press V/V repeatedly until “LEVEL” appears, then press © or b. 3 Press V/V repeatedly until “T. TONE” appears, then press © or b. 4 Press V/V repeatedly to select “T. TONE Y”, then press ©. The test tone is output from each speaker in sequence as follows: Front left —► Center —► Front right —► Surround right —t Surround left —t Subwoofer 5 Press B until “T. TONE” appears. 6 Press V/V repeatedly to select the desired speaker, then press © or b. The test tone is emitted from the speaker that is being adjusted only. • FL LVL: adjusts the front left speaker level. • CNT LVL: adjusts the center speaker level. • FR LVL: adjusts the front right speaker level. • SR LVL: adjusts the surround right speaker level. • SL LVL: adjusts the surround left speaker level. • SW LVL: adjusts the subwoofer level. Notes • “CNT LVL” does not appear when you set “CNT N” in the “SP SETUP” setting. • “SR LVL” and “SL LVL” do not appear when you set “SUR N” in the “SP SETUP” setting. 7 Press V/V repeatedly to adjust the speaker level, then press © or b. You can adjust from -6.0 dB to +6.0 dB in 0.5 dB steps. Note If you do not adjust for a certain period, the test tone is emitted from the next speaker in sequence. 8 Repeat step 6 and 7 to adjust the other speaker level. 9 After you have finished making adjustments, press V/V until “T. TONE” appears, then press © or b. 10p ress V/V repeatedly to select “T. TONE N”, then press ©. 11 Press AMP MENU. The AMP menu turns off. When a test tone is not output from the speakers • The speaker cords may not be connected securely. • The speaker cords may have the short-circuit problem. • The test tone signals are not output from the HDMI...
Ce manuel est également adapté pour les modèles :Home cinéma - HT-SS360 (996.94 kb)