Évaluations - 3, GPA: 4.3
(
)
)
|
Par ce dispositif a également d'autres instructions :
Facilité d'utilisation
• Do not pull by the cord when you unplug the AC adapter cord. 26GB Selecting the installation position of the main unit Selecting the installation position of the main unit To install the main unit in a vertical position See “Attaching the covers” (page 28). To install the main unit in a horizontal position Refer to the supplied “Main Unit Installation Guide.” To install the main unit on a wall Refer to the supplied “Main Unit Installation Guide.” Contact an installer to install the main unit on a wall. • To install the main unit on a wall, you need the wall mounting brackets A and B. These are not supplied with BDVL600, so purchase the brackets (WS-L100) if necessary. 27GB Getting Started 28GB Getting Started After you have made all the connections, organize the cables and attach the panel cover and the stand cover by following the Steps below. 1 Place the main unit on its face. • Make sure to place the main unit on a soft thick cloth to prevent damaging the main unit. 2 Bring together the cables (except the FM wire antenna (aerial)), guide them through the slot at the right of the main unit, behind the clamp (A), and through the slot at the bottom of the main unit. Thread the FM wire antenna (aerial) through the small indentation at the rear of the main unit. 3 Thread the AC power cord (mains lead) through the gap on the main unit by securing it behind the tabs, guide it through the slot at the left of the main unit, behind the clamp (B), and through the slot at the bottom of the main unit. Attaching the covers FM wire antenna (aerial) Tabs 29GB Getting Started 4 Attach the panel cover to the rear of the main unit. Put the left edge of the lower part of the panel cover on (C), align the bottom projection of the panel cover with (D), and then slide it inward until it clicks into place. • Be sure to fully extend the FM wire antenna (aerial). • After attaching the panel cover, keep the FM wire antenna (aerial) as horizontal as possible. • If a USB device (such as a USB memory) that has a long, thin body to the side panel, use the (USB) port on the left side of the main unit. 5 Attach the stand cover to the rear of the main unit. Align both edges of lower part of the stand cover with the guides on the stand (E), and then slide the stand cover down gently. To remove the stand cover Place the main unit on its face. Press the catches on the stand down and slide the stand cover in the direction of the arrow in the illustration below. FM wire antenna (aerial) Gettin g Star ted Getting Started To arrange the cables to the left side of the main unit, open the hatch of the panel cover before you attach the panel cover. Be sure not to lose the hatch. Hatch To open the hatch, remove the panel cover, hold the hatch, and then pull it up and outward. To close the hatch, align the projection of the hatch with the projection opening on the panel cover, and then gently push in and down on the hatch until it clicks. To open the hatch To close the hatch 30GB Turning on the system Turning on the system 1 Press "/1 to turn the main unit on. "/1 2 Connect the AC power cord (mains lead) of the subwoofer into the wall outlet (mains). After the subwoofer turns on, the LINK/STANDBY indicator turns green and the wireless transmission is activated. LINK/STANDBY indicator • If the LINK/STANDBY indicator does not turn on, see “Subwoofer” (page 13) and “Sound” (page 71). About the standby mode The subwoofer enters standby mode automatically (the LINK/STANDBY indicator turns red) when the main unit is in standby mode or wireless transmission is deactivated. The subwoofer turns on automatically (the LINK/STANDBY indicator turns green) when the main unit is turned on and wireless transmission is activated. To specify the wireless connection If you use multiple wireless products or your neighbors use wireless products, interference may occur. To prevent this, you can specify the wireless connection to link the main unit to the subwoofer (Secure Link function). For details, see “Further Settings for the Wireless System” (page 55). 31GB Getting Started Getting Started Getting Started Follow the Steps below to make the basic adjustments for using the system. Displayed items vary depending on the country model. 8 0 97 5 64 2 31 "/1 C/X/x/c, HOME 1 Turn on the TV. 2 Press [/1. 3 Switch the input selector on your TV so that the signal from the system appears on the TV screen. The Easy Setup Display for OSD language selection appears. 4 Perform the [Easy Setup]. Follow the on-screen instructions to make the basic settings using C/X/x/c and . Depending on the connection method (page 19), perform the following setting. • HDMI cable connection: Follow the instructions that are displayed on the TV screen. • Video cord connection: Select [16:9] or [4:3] so that the picture is displayed correctly. To recall the Easy Setup Display 1 Press HOME. The home menu appears on the TV screen. 2 Press C/c to select [Setup]. 3 Press X/x to select [Easy Setup], then ...
Ce manuel est également adapté pour les modèles :Home cinéma - BDV-L800 (2.93 mb)
Home cinéma - BDV-L800M (2.93 mb)