Log:
Évaluations - 3, GPA: 4 ( )

Instructions Global Machinery Company, Modèle GTX144100K

Fabricant : Global Machinery Company
Taille : 2.86 mb
Nom Fichier : 62dc5170-b6d0-8b44-8d57-9de7f3787363.pdf
Langue d'enseignement: en
Aller à la télécharger



Facilité d'utilisation


When the 9 battery indicator is showing only 1 LED (low) the battery should be removed and put on the charger. LED Work area light The drill has 3 LED lights (11) to illuminate the work area and improve vision when drilling in areas with insufficient light. To turn the LED lights on and off depress the LED light switch (13). Using the drill Use the forward/reverse switch (4) to select the direction of rotation, then pull the trigger (3). This trigger switch is an electronic variable speed control which enables the user to vary the speed continuously. The speed varies according to how far the trigger switch is depressed, the further it is depressed the faster the chuck will rotate and the lighter it is depressed, the slower it will rotate. To stop the drill, release the trigger switch. Note. You can only change the direction of rotation of the drill using the forward/reverse switch when the trigger is NOT depressed. Forward/reverse switch This switch (4) will allow you to change the direction of the motor while the trigger switch is not depressed. Drilling uses the forward mode. The reverse mode is intended for the removal of screws. Adjustable torque This drill is equipped with 20 torque settings plus one drill setting which are controlled by the torque collar (2). By rotating the collar behind the chuck, it is possible to adjust the torque. This will allow better control when using the drill as a screwdriver as it prevents over-tightening of the screws. For drilling, always use the use the Drill position by aligning the Drill symbol with the triangular indicator on the front face of the drill near the torque collar. For setting the torque position, select a low setting on the torque collar and align the selected symbol with the triangular indicator on the top of the drill. Increase gradually to set the correct torque. It is better to use a scrap piece of material if possible to set the torque. Inserting and removing bits This drill has a keyless chuck, which means that a chuck key is not needed to secure a bit in the drill. 1. Open the chuck by holding the rear section of the chuck firm and rotating the front section in a anti-clockwise direction, sufficiently enough to allow the drill bit required to fully enter the jaws of the chuck. 2. Ensure the drill bit is fully inserted, so that the chuck jaws grip the straight section of the bit. 3. Holding the rear section of the chuck firmly, rotate the front section of the chuck clock-wise until the jaws 10 tighten on the drill bit. The front section of the chuck needs to be tightened firmly to ensure the drill bit is held securely. 4. To remove the drill bit, hold the rear section of the chuck firmly and rotate sharply the front section of the chuck in a anti-clockwise direction, sufficiently enough to allow the drill bit to be removed. Adjustable side handle 1. Turn the side handle clamp knob (6) anti-clockwise to loosen the collar fully and slip it over the chuck (1) onto the drill. 2. Adjust the position of the side handle (5) to suit the application and tighten the side handle clamp knob (6) to secure it in place. Drilling Drilling metals • Always clamp sheet metal. • Support thin metal with a block of wood to avoid distorting it. • Use a punch to mark the centre of the hole. • Use a suitable lubricant for the material you are working on, USE: FOR: Oil Steel Turpentine or paraffin Aluminium Do not lubricate Brass, copper or cast iron Drilling plastics and plastic coated chipboard • Use high speed drill bits • See drilling wood below Drilling masonry • This drill is not designed for drilling masonry. Purchase or hire a Hammer drill. Drilling wood • Clamp a piece of scrap wood to the back of your work to prevent splintering. All drilling operations • Mark off the centre of the hole using a centre punch or nail. • Don’t force the drill, let it work at its own pace • Keep the drill bit sharp. • Reduce pressure, as the drill is about to break through the item being drilled. Chuck replacement The chucks of reversible drills are always fixed by a screw with a left-hand thread. The screw, which is located in the centre of the chuck, must be removed before the chuck can be removed. To remove the screw, turn it in a clockwise direction. The chuck can now be removed by unscrewing it anti-clockwise. If you have trouble removing the chuck take the drill to your nearest authorised service centre for chuck replacement. Caution. Always ensure that the drill is switched off and the battery pack is removed before making any adjustments. Maintenance • Store the tools, instruction manual and where necessary the accessories in the original packaging. In this way you will always have all the information and parts ready to hand. • Do not throw used batteries into fire or water. There is a danger of explosion! Please hand in non-working or used batteries, or tools with built-in batteries, to the environmentally-safe disposal unit at a municipal waste- disposal centre, or to your d...


Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories