Évaluations - 1, GPA: 3
(
)
)
|
Facilité d'utilisation
There is a danger of electric shock. Do not position the tool or battery charger near water; for example, near a sink, wash bowl or toilet. Do not spill liquid of any kind on the tool or charger. Doing so may short out parts, causing damage to the product and creating the risk of fire or electric shock. • Take the tool or charger to your nearest Authorised Service centre or phone and speak with an experienced GMC Customer Service Representative for assistance in these circumstances: • If liquid has been spilled into the tool or charger, or if rain or water has touched the screwdriver or charger. • If the tool or charger does not operate normally after you follow the operating instructions. • If the tool or charger has been dropped or damaged. • If the tool or charger exhibits a distinct degradation in performance. • If the tool or charger is damaged in any way. • If the screwdriver is not charged within the time frame as specified in this manual, turn charger off. • To reduce the risk of an electric shock, unplug the charger from the power supply before attempting to clean it. To clean tool or charger, wipe with a damp cloth. Use of any other cleaners is not recommended. • Do not place any object on to, or allow anything to rest on the charger. • Make sure that the charger cable is positioned where it will not be stepped on, tripped over or otherwise subjected to damage or stress. Keep the lead away from operating machinery. • Do not pull on the lead of the charger to disconnect it from the mains power socket. • Do not use an extension cord unless it is absolutely necessary. The use of an improper extension cord could cause the risk of fire, electric shock or electrocution. • Never attempt to connect two chargers together. • Do not charge or use the tool in locations where the temperature may be below 0°C or exceed 40°C such as alongside sheds or metal structures. • The screwdriver can be charged or operated at temperatures between 0° C and 40° C. The most suitable temperatures to charge the screwdriver are between 20 - 25° C. When to charge the tool • New tools are shipped in a low charge condition and must be fully charged before use. It takes approximately 45 seconds to fully charge the tool. • Charging the tool should not be undertaken casually. Through the charging cycle monitor the tool and make sure that screwdriver is charging. This can be done by reviewing the charging process indicators (6) and the charge cycle completed indicator (5). Note. You may use the screwdriver at any time. The charging process does not have to be completed to use the tool and short chargers will not harm the tool. Know your product This screw driver is for light to medium applications of screws and small nuts and bolts. If the screw driver is unable to rotate the fastener do not over load by holding the switch in the on position and manually rotating the fastener. 1. Chuck/Bit retainer 2. Handle adjusting switch 3. Forward/Reverse switch 4. Trigger 5. Charge cycle completed indicator 6. Charging process indicators 7. Charger 8. Charger power cord 9. Accessory bits storage 10. Power on indicators 1 2 3 4 10 5 6 9 7 8 Unpacking Due to modern mass production techniques, it is unlikely that your GMC Power Tool is faulty or that a part is missing. If you find anything wrong, do not operate the tool until the parts have been replaced or the fault has been rectified. Failure to do so could result in serious personal injury. Important information – special product care Your GMC quick charge screwdriver uses capacitors to store the energy that operates the screwdriver. Do not attempt to charge the screwdriver with any other charger than the one supplied. IT IS DANGEROUS TO USE ANY OTHER CHARGER TO CHARGE YOUR TOOL. Ensure you have read all of the safety notes in the previous pages before using the screwdriver. Charging IMPORTANT. Before plugging in the charger (7) into the mains power supply always ensure that the mains power switch is turned off. IMPORTANT. The tool will be fully charged after approximately 45 seconds. The screwdriver can remain in the charger, with the charger turned on without damage being done to the cells (Note. Do not leave the screwdriver in the charger turned on unattended). 1. Place the screwdriver into the charger (7) vertically with the bottom of the screwdriver aligning with the charger as per the picture shown. Push the screwdriver down until it is securely in place. Note. If the screwdriver is incorrectly orientated the screwdriver will not fit securely in the base. 2. Plug in the charger and switch on at the power supply. The power on indicators (10) will glow signalling that the charger has power connected to it. The screwdriver will now begin charging. While the screwdriver is charging the charging indicators (6) will glow signalling that the screwdriver is in the charging process. When the screwdriver charging process is complete the charge cycle completed indicator (5) will glow advising that th...