Évaluations - 2, GPA: 3.5
(
)
)
|
Facilité d'utilisation
4. Keep hands away from all cutting edges and moving parts. 5. Wear ear protectors when using the tool for extended periods. Prolonged exposure to high intensity noise can cause hearing loss. Symbology Properly Recycle Nickel Cadmium Batteries Direct Current Underwriters Laboratories, Inc. No Load Revolutions per Minute (RPM) Specifications Cat. No. Volts DC No Load RPM No Load Blows per Minute 0613-20 14.4 Low 0-500 High 0-1700 Low 0-7500 High 0-25500 0614-20 14.4 Low 0-500 High 0-1700 Low 0-7500 High 0-255000616-20 14.4 Low 0-500 High 0-1700 N/A0622-20 18 Low 0-500 High 0-1700 N/A 0624-20 18 Low 0-500 High 0-1700 Low 0-7500 High 0-25500 4 FUNCTIONAL DESCRIPTION 1 2 3 4 5 6 8 1. Speed selector 2. Battery latch 3. Battery pack 4. Trigger 5. Control switch 6. Keyless chuck 7. Side handle 8. Torque selector collar 7 Capacities Wood Steel Flat Bit Auger Bit Hole Saw Screws (dia.) Masonry 0613-20 0614-20 0616-20 0622-20 0624-20 1/2" 1/2" 1/2" 1/2" 1/2" 1-1/2" 1-1/2" 1-1/2" 1-1/2" 1-1/2" 1-1/8" 1-1/8" 1-1/8" 1-1/8" 1-1/8" 2-1/8" 2-1/8" 2-1/8" 2-1/8" 2-1/8" 1/4" 1/4" 1/4" 1/4" 1/4" 3/8" 3/8" N/A N/A 3/8" 5 CHARGING & USING BATTERY PACKS WARNING! Charge only MILWAUKEE 12, 14.4 and 18 Volt battery packs in chargers. Other types of batteries may explode causing personal injury and damage. Charge your battery pack before you use your tool for the first time and when your tool no longer performs with the power and torque needed for the job. Never completely discharge the battery pack. Standard charging time will vary according to the type of charger you use. The charging time will also vary depending on the supply voltage and charge needed. For example, if your battery pack does not require a full charge, charging time will be less. FOR SPECIFIC CHARGING INSTRUCTIONS, PLEASE READ THE CHARGER OPERATOR'S MANUAL SUPPLIED WITH YOUR CHARGER. Battery packs are affected by temperature. Your battery pack will perform best and have longest life if it is charged when the temperature is between 60°-80°F (15°27° C). Do not charge in temperatures below 40°F (5°C) or above 105°F (40°C). Under these conditions, capacity will be reduced. (See “Maintenance"). Inserting Battery Pack into Tool (Fig. 1 & 2) Battery pack can be inserted into the tool in two ways. Fig. 1 1.For working in restricted spaces. Insert the battery pack from the front by sliding battery pack into the body of the tool. Insert the battery pack until the battery latches lock. Fig. 2 2. For optimum weight distribution and balance. Insert the battery pack from the back by sliding the battery pack into the body of the tool. Insert the battery pack until the battery latches lock. 3. To remove the battery pack, press in both battery latches and slide the battery pack off of the tool. 6 WARNING! ASSEMBLY Always lock trigger or remove battery pack before changing or removing accessories. Only use accessories specifically recommended for this tool. Others may be hazardous. WARNING! To reduce the risk of injury, always use a side handle when using this tool. Always brace or hold securely. Installing the Side Handle 1. To install the side handle, loosen the side handle grip until the ring is large enough to slide over the torque selector collar. The raised rib on the side handle ring fits inside the groove around the tool. Rotate the handle to the desired position and tighten the side handle until it is secure. 2. To remove the side handle, loosen the side handle grip until the ring is large enough to slide off the tool. OPERATION WARNING! To reduce the risk of injury, wear safety goggles or glasses with side shields. ratcheting sound and the sleeve can not be rotated any further. 3. To remove the bit, turn the sleeve in the counterclockwise direction. NOTE: A ratcheting sound may be heard when the chuck is opened or closed. This noise is part of the locking feature, andWARNING! ASSEMBLY Always lock trigger or remove battery pack before changing or removing accessories. Only use accessories specifically recommended for this tool. Others may be hazardous. WARNING! To reduce the risk of injury, always use a side handle when using this tool. Always brace or hold securely. Installing the Side Handle 1. To install the side handle, loosen the side handle grip until the ring is large enough to slide over the torque selector collar. The raised rib on the side handle ring fits inside the groove around the tool. Rotate the handle to the desired position and tighten the side handle until it is secure. 2. To remove the side handle, loosen the side handle grip until the ring is large enough to slide off the tool. OPERATION WARNING! To reduce the risk of injury, wear safety goggles or glasses with side shields. ratcheting sound and the sleeve can not be rotated any further. 3. To remove the bit, turn the sleeve in the counterclockwise direction. NOTE: A ratcheting sound may be heard when the chuck is opened or closed. This noise is part of the locking feature, and Using Keyless Chucks (Fig...
Ce manuel est également adapté pour les modèles :Perceuses et shuropopverty - Hammer-Drill (2.03 mb)
Perceuses et shuropopverty - Hammer-Drill (2.03 mb)
Perceuses et shuropopverty - Hammer-Drill (2.03 mb)