Évaluations - 4, GPA: 3.3
(
)
)
|
Facilité d'utilisation
This feature will lock the bit holder in one position when the trigger switch is released. This will allow you to tighten or loosen a nut or screw by rotating the tool by hand with the switch off. This is convenient when higher turning torque is needed. BUILT IN WORK LIGHT Your tool is also equipped with a light that turns on automatically when the switch is activated, for better visibility when drilling/driving (Fig. 1). INSERTING AND RELEASING BATTERY PACK Release battery pack from tool by pressing on both sides of the battery release tabs and pull downward (Fig. 4). To insert battery, align battery and slide battery pack into tool until it locks into position. Do not force. A WARNING If battery release tabs are cracked or otherwise damaged, do not insert into tool. Battery can fall out during operation. BATTERY RELEASE TABS FIG. 4 IMPORTANT CHARGING NOTES 1. The charger was designed to fast charge the battery only when the battery temperature is between 32°F (0°C) and 113°F (45°C). If the battery pack is too hot or too cold, the charger will not fast charge the battery. (This may happen if the battery pack is hot from heavy use). When the battery temperature returns to between 32°F (0°C) and 113°F (45°C), the charger will automatically begin charging. 2. A substantial drop in operating time per charge may mean that the battery pack is nearing the end of its life and should be replaced. 3. Remember to unplug charger during storage period. 4. If battery does not charge properly: a. Check for voltage at outlet by plugging in some other electrical device. -9- BM 2610007871 12-09:BM 2610007871 12-09 12/17/09 7:25 AM Page 10 b. Check to see if outlet is connected to a light switch which turns power “off” when lights are turned off. c. Check battery pack terminals for dirt. Clean with cotton swab and alcohol if necessary. d. If you still do not get proper charging, take or send tool, battery pack and charger to your local Bosch Service Center. See “Tools, Electric” in the Yellow Pages for names and addresses. Note: Use of chargers or battery packs not sold by Bosch will void the warranty. CHARGER INDICATORS, SYMBOLS AND MEANING (Model BC430) If the indicator lights are “OFF”, the charger is not receiving power from power supply outlet. I I I B ci If the green indicator light is “ON”, the charger is plugged in but the battery pack is not inserted, or the battery pack is fully charged and is being trickle charged. If the red indicator light is “ON”, the battery pack is too hot or cold for fast-charging. The charger will switch to trickle charge, until a suitable temperature is reached, at which time the charger will switch automatically to fast-charging. If the green indicator light is “BLINKING”, the battery pack is being fast-charged. Fast-charging will automatically stop when the battery pack is fully charged. *8 If the red indicator light is “BLINKING”, the battery pack cannot accept a charge or the contacts of the charger or battery pack are contaminated. Clean the contacts of the charger or battery pack only as directed in these operating instructions or those supplied with your tool or battery pack. The lithium ion battery is protected against deep discharging by the “Electronic Cell Protection (ECP)”. When the battery is empty, the tool is switched off by means of a protective circuit. The battery is supplied partially charged. Completely charge the battery before using your cordless screwdriver for the first time. The lithium ion battery can be charged at any time, without reducing its service life. Interrupting the charging procedure does not damage the battery. Plug charger cord into your standard power outlet, then insert battery pack into charger (Fig. 5). The charger’s green indicator light will begin to “BLINK”. This indicates that the battery is receiving a fast charge. Fast-charging will automatically stop when the battery pack is fully charged. CHARGING BATTERY PACK (Model BC430) When the indicator light stops “BLINKING” (and becomes a steady green light) fast charging is complete. The battery pack may be used even though the light may still be blinking. The light may require more time to stop blinking depending on temperature. When you begin the charging process of the battery pack, a steady red light could also mean the battery pack is too hot or too cold. The purpose of the green light is to indicate that the battery pack is fast-charging. It does not indicate the exact point of full charge. The light will stop blinking in less time if the battery pack was not completely discharged. When charging several batteries in sequence, the charge time may slightly increase. When the battery pack is fully charged, unplug the charger (unless you're charging another battery pack) and slip the battery pack back into the tool. -10- CHARGER INDICATORS, SYMBOLS AND MEANING (Model BC330) If the indicator lights are “OFF”, the charger is not receiving power from ...